Repareer je spullen

Recht op reparatie

Winkel

Epson Stylus Photo 1400 Housing Replacement

Geschreven door: Larry Huang (en 8 andere bijdragers)
  • Reacties: 3
  • Favorieten: 0
  • Voltooide reparaties: 7

Moeilijkheid

Eenvoudig

Stappen

12

Tijd vereist

15 - 30 minuten

Secties

1

Markeringen

0

Inleiding

To get to the inside parts of the printer, the housing components must come off.

  1. Turn off the printer.

    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

    Vertaal

  2. Locate the IEEE cover in the back. Gently slide the cover to the right to unlatch, then pull to remove it.

    • Locate the IEEE cover in the back.

    • Gently slide the cover to the right to unlatch, then pull to remove it.

    Vertaal

    errore avevo chiesto informazioni x sostituire la batteria al cellulare HUAWEI Mod. LX1

    Luigi Martinenghi - Antwoord

    avevo chiesto informazioni x la sostituzione della batteria cellulare HUAWEI Mod.LX1

    Luigi Martinenghi - Antwoord

  3. Using a Phillips #2 screwdriver, remove the four 10 mm screws shown. Remove the 6 mm screw that holds the rear housing in place.

    • Using a Phillips #2 screwdriver, remove the four 10 mm screws shown.

    • Remove the 6 mm screw that holds the rear housing in place.

    Vertaal

  4. Remove the rear housing by pulling it backwards. Remove the rear housing by pulling it backwards.

    • Remove the rear housing by pulling it backwards.

    Vertaal

  6. Insert a plastic opening tool into the cutouts of the lower housing. Release the two tabs of the side housing by lifting the tool in an upward motion. Remove the side housing by pulling it outwards.

    • Insert a plastic opening tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion.

    • Remove the side housing by pulling it outwards.

    Vertaal

  7. Both side housings are attached by the same type of mechanism. Using the same method, remove the other side housing.

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

    Vertaal

  8. Lift the paper support. Open the printer cover and front cover. Open the printer cover and front cover.

    • Lift the paper support.

    • Open the printer cover and front cover.

    Vertaal

  9. Remove the four 10 mm Phillips #2 screws from the sides of the printer. Remove the three 6 mm Phillips #2 screws. Remove the three 6 mm Phillips #2 screws.

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6 mm Phillips #2 screws.

    Vertaal

  10. Detach the tabs from the pins on each side by pulling it outwards. Detach the tabs from the pins on each side by pulling it outwards.

    • Detach the tabs from the pins on each side by pulling it outwards.

    Vertaal

  11. Remove the two 10 mm Phillips #2 screws on the front of the printer. Remove the two 10 mm Phillips #2 screws on the front of the printer.

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

    Vertaal

  12. Disconnect the cable on the side by carefully pulling it outwards. You may need to gently rock the cable up and down while pulling. You may need to gently rock the cable up and down while pulling.

    • Disconnect the cable on the side by carefully pulling it outwards.

    • You may need to gently rock the cable up and down while pulling.

    Vertaal

  13. Remove the upper housing by lifting it upwards. It's easier to lift the housing by gripping it from the bottom.

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

7 andere personen hebben deze handleiding voltooid.

Auteur

met 8 andere bijdragers

Larry Huang

Lid sinds: 12-10-11

839 Reputatie

4 handleidingen geschreven

Badges: 14

+11 andere badges

Team

Cal Poly, Team 17-11, Regan Fall 2011 Lid van Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 Leden

6 handleidingen geschreven

Één commentaar

Voeg een opmerking toe

Thank you so much, Larry! I am repurposing my 1400 for sublimation printing and need to get the print head a little easier than standard methods! Much appreciated!

ryan Caputo - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 3

Afgelopen 30 dagen: 20

Altijd: 6,549