Grip the lower portion of the back of the phone and slide downwards.
  • Grip the lower portion of the back of the phone and slide downwards.

Voeg opmerking toe

Lift battery at the rounded notch near the bottom of the phone.
  • Lift battery at the rounded notch near the bottom of the phone.

Voeg opmerking toe

Unscrew the four Torx screws from the backplate.
  • Unscrew the four Torx screws from the backplate.

  • The backplate may begin to separate from the keypad face. Do not try to remove it yet.

  • The screws are T5 Torx screws, 5.6mm.

Voeg opmerking toe

Swivel the phone open.
  • Swivel the phone open.

Voeg opmerking toe

Using the Spudger, gently pry up the U-shaped grey cover below the keypad.
  • Using the Spudger, gently pry up the U-shaped grey cover below the keypad.

  • The cover is secured with adhesive tape. The gentler this is removed, the easier it will be to reassemble.

Voeg opmerking toe

Remove the two Torx screws from below the cover.
  • Remove the two Torx screws from below the cover.

  • These are T5 Torx screws, 8.6mm.

Voeg opmerking toe

Gently work a spudger or a fingernail between the keypad face and the backplate.
  • Gently work a spudger or a fingernail between the keypad face and the backplate.

  • The pieces are clipped together most tightly at the bottom loop section.

Voeg opmerking toe

Separate the keypad face from the backplate. The keypad keys and the button component are both loose inside the phone, so take note of their orientation in case they become dislodged.
  • Separate the keypad face from the backplate.

  • The keypad keys and the button component are both loose inside the phone, so take note of their orientation in case they become dislodged.

  • Take note of the braided cord's state. Upon reassembly it should be returned to the same orientation.

Voeg opmerking toe

Holding the backplate away from the swivel, remove the 4 small Phillips screws and both stamped struts from the swivel assembly. Note that only the bottom strut has a tab. The screws are Phillips, 2.9mm
  • Holding the backplate away from the swivel, remove the 4 small Phillips screws and both stamped struts from the swivel assembly.

  • Note that only the bottom strut has a tab.

  • The screws are Phillips, 2.9mm

Voeg opmerking toe

The back housing is now disassembled, and the swivel assembly is revealed.
  • The back housing is now disassembled, and the swivel assembly is revealed.

Voeg opmerking toe

Remove the four black Phillips screws holding the swivel assembly to the LCD section of the phone. Be mindful of the screws, as they are very small.
  • Remove the four black Phillips screws holding the swivel assembly to the LCD section of the phone.

  • Be mindful of the screws, as they are very small.

  • The screws are Phillips, 2.4mm

Voeg opmerking toe

Gently remove the grey plastic cover at the top-rear of the LCD section with a spudger.
  • Gently remove the grey plastic cover at the top-rear of the LCD section with a spudger.

  • It is secured with adhesive tape, the more gently you remove this piece, the easier reassembly will be later.

Voeg opmerking toe

Remove the two Torx screws revealed under the grey cover.
  • Remove the two Torx screws revealed under the grey cover.

  • The screws are Torx T5, 5.6mm

Voeg opmerking toe

Gently pry off the front face, starting at the bottom slot.
  • Gently pry off the front face, starting at the bottom slot.

Voeg opmerking toe

Remove the Torx screws near the buttons.
  • Remove the Torx screws near the buttons.

  • The screws are Torx T5, 5.6mm

Voeg opmerking toe

Remove the black front plate. Remove the button overlay, taking note of its position for reassembly. There are small grey nubs that correspond to holes in the overlay.
  • Remove the black front plate.

  • Remove the button overlay, taking note of its position for reassembly. There are small grey nubs that correspond to holes in the overlay.

Voeg opmerking toe

Gently release the small grey retaining clips around the outside of the display assembly.
  • Gently release the small grey retaining clips around the outside of the display assembly.

  • Separate the display assembly from its backplate.

  • Take care; some of the side buttons may dislodge as the backplate is separated.

  • The LCD section is now disassembled.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Beau Blanchard

Lid sinds: 30-09-12

20 Reputatie

12 handleidingen geschreven

Team

University of Maine, Team 1-5, Diaz Fall 2012 Lid van University of Maine, Team 1-5, Diaz Fall 2012

UMAINE-DIAZ-F12S1G5

1 Lid

12 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 6

Altijd: 393