Onderdelen

Geen onderdelen nodig.

Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws) Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)
  • Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)

Put a notice on here that the screws are very small and are easy to misplace while disassembling device. Also, while disassembling the device there was only one screw present, where the guide suggested there were three.

Curtis Reedy - Antwoord

Before beginning, put a note that the camera should be turned off before proceeding.

Curtis Reedy - Antwoord

Add a note at the beginning of the guide that there are a large number of small screws that should be separated as the steps are completed.

Curtis Reedy - Antwoord

There's a capacitor .....watch out for it in every step.

BILL BOYD - Antwoord

Remove the right side panel by pulling off the large silver piece.
  • Remove the right side panel by pulling off the large silver piece.

There is no reference to removing screws from the right side panel, where it is necessary to remove 2 screws to do so.

Curtis Reedy - Antwoord

Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws) Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)
  • Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)

Voeg opmerking toe

Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)
  • Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)

Voeg opmerking toe

Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.
  • Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.

Voeg opmerking toe

Remove 3 screws from the front of the camera using a #00 screwdriver. Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side) Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)
  • Remove 3 screws from the front of the camera using a #00 screwdriver.

  • Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)

Wrong point of focus for the second picture. What should be in focus is very blurry.

Curtis Reedy - Antwoord

Using a plastic spudger, lift up the black clips. Still using the plastic spudger, detach the gold connector strip and white connector strip. Using both hands, pull the camera apart into two pieces.
  • Using a plastic spudger, lift up the black clips.

  • Still using the plastic spudger, detach the gold connector strip and white connector strip.

  • Using both hands, pull the camera apart into two pieces.

There were multiple gold strips, so the one that needs to be pulled should be highlited in the picture.

Curtis Reedy - Antwoord

in step seven pull up the black bar of the ZIF connectors before pulling out the white or gold ribbons

Curtis Reedy - Antwoord

Conclusie

To reassemble your device, follow these instructions in reverse order.

Max McIntyre

Lid sinds: 21-01-11

511 reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 13-4, Forte Winter 2011 Lid van Cal Poly, Team 13-4, Forte Winter 2011

CPSU-FORTE-W11S13G4

6 Leden

6 handleidingen geschreven

Één commentaar

How did you get the ring around the lens off?? I can't seem to find that step and in all the pictures it's already off

Maureen - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 5

Altijd: 2,490