Repareer je spullen Gemeenschap Winkel

Deze handleiding heeft recentere wijzigingen. Schakel over naar de nieuwste niet-geverifieerde versie.

Disassembling Nerf Recon CS-6 Shell

Inleiding

This is a prerequisite to replacing any other piece. This guide involves removing most of the screws in the shell and splitting the gun along the middle seam.

Wat je nodig hebt

  1. Disassembling Nerf Recon CS-6 Shell, Remove Magazine: stap 1, afbeelding 1 van 1

    • Skip this step if magazine is already removed.

    • Pull slide back.

    • Pull backwards on release buttons and slide magazine out.

    • Push slide back forward and pull trigger.

    Vertaal

    My priming bar is stuck how do I fix this?

    Ethan - Antwoord

  2. Disassembling Nerf Recon CS-6 Shell, Remove Visible Screws: stap 2, afbeelding 1 van 1

    • Use the Phillips #0 Screwdriver to remove these 9 screws.

    • All screws marked in red are 9.6 mm Phillips #0 screws.

    • Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

    Vertaal

  4. Disassembling Nerf Recon CS-6 Shell, Remove Hidden Screws: stap 3, afbeelding 1 van 2 Disassembling Nerf Recon CS-6 Shell, Remove Hidden Screws: stap 3, afbeelding 2 van 2

    • Pull slide back to reveal more screws.

    • Remove these 2 screws.

    • Push slide forward.

    • Pull trigger to release compression of the main spring.

    • Screws are 9.6 mm Phillips #0.

    • Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

    Vertaal

    Lost the trigger spring. What spec of spring can I replace it with?

    derekpearcy - Antwoord

  5. Disassembling Nerf Recon CS-6 Shell, Remove Plunger Cap: stap 4, afbeelding 1 van 1

    • Remove the screws on the plunger cap.

    • Tug the plunger cap off.

    • Screws are 9.6 mm Phillips #0.

    Vertaal

  6. Disassembling Nerf Recon CS-6 Shell, Remove Slide Screws: stap 5, afbeelding 1 van 1

    • Remove the 2 screws on the slide.

    • Screws are 9.6 mm Phillips #0.

    • Hold the two halves of the gun together to prevent any springs from launching out.

    Vertaal

  7. Disassembling Nerf Recon CS-6 Shell, Split the Gun in Half: stap 6, afbeelding 1 van 2 Disassembling Nerf Recon CS-6 Shell, Split the Gun in Half: stap 6, afbeelding 2 van 2

    • Pull the gun apart at the middle seam.

    • Watch for any springs that might launch out.

    Vertaal

    Pay attention to the orientation of the tabs on the compression tube. The tabs fit into grooves on the side of the gun. This tripped me up.

    Bob - Antwoord

Conclusie

To reassemble your device, follow these instructions in reverse order.

11 andere personen hebben deze handleiding voltooid.

Auteur

met 3 andere bijdragers

Asad Qureshi

Lid sinds: 10/22/14

586 Reputatie

3 handleidingen geschreven

Medailles: 17

+14 andere badges

Team

Baylor, Team 8-14, Williams Fall 2014 Lid van Baylor, Team 8-14, Williams Fall 2014

BU-WILLIAMS-F14S8G14

3 Leden

6 handleidingen geschreven

2 opmerkingen

Does anyone have a spare spring for this gun I am missing mine

The Lazy Gamer - Antwoord

very useful, thanks!

Sebastian Isaacs - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 3

Afgelopen 7 dagen: 18

Afgelopen 30 dagen: 49

Altijd: 11,712