Ga door naar hoofdinhoud

Disassembling General Electric Telephone 2-9710A Handset

Wat je nodig hebt

  1. Disassembling General Electric Telephone 2-9710A Handset, Phone Cord: stap 1, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset, Phone Cord: stap 1, afbeelding 2 van 2
    • Unplug the device before proceeding.

    • Using a plastic opening tool, remove the phone cord from the phone jack at the base of the headset.

    • To release the cable, gently press down on the top plastic tab of the connector.

  2. Disassembling General Electric Telephone 2-9710A Handset: stap 2, afbeelding 1 van 3 Disassembling General Electric Telephone 2-9710A Handset: stap 2, afbeelding 2 van 3 Disassembling General Electric Telephone 2-9710A Handset: stap 2, afbeelding 3 van 3
    • Remove the 7.5 mm screw.

    • Remove the screw cap.

    • Pull up the phone cord to remove it from the base.

  3. Disassembling General Electric Telephone 2-9710A Handset, General Electric Telephone 2-9710A Handset: stap 3, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset, General Electric Telephone 2-9710A Handset: stap 3, afbeelding 2 van 2
    • Remove the plastic cover with a plastic opening tool by gently sliding the tool underneath the plastic and pry the cover off.

  4. Disassembling General Electric Telephone 2-9710A Handset: stap 4, afbeelding 1 van 1
    • Remove the paper with a plastic opening tool by gently sliding the tool underneath and prying the paper away from the phone.

  5. Disassembling General Electric Telephone 2-9710A Handset: stap 5, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset: stap 5, afbeelding 2 van 2
    • Remove the rubber stopper with a plastic opening tool by gently sliding the tool underneath and pry away from the phone.

  6. Disassembling General Electric Telephone 2-9710A Handset: stap 6, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset: stap 6, afbeelding 2 van 2
    • Remove the two 2.1 mm screws with a Phillips #1 screwdriver.

  7. Disassembling General Electric Telephone 2-9710A Handset: stap 7, afbeelding 1 van 1
    • Pull apart the handset by pulling the top shell away from the other half of the phone.

  8. Disassembling General Electric Telephone 2-9710A Handset: stap 8, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset: stap 8, afbeelding 2 van 2
    • Remove 3 screws attaching the motherboard to shell.

    • Remove the 13 mm screw with a Philips #1 screwdriver.

    • Remove the two 13 mm screws with washers with a Philips #1 screwdriver.

  9. Disassembling General Electric Telephone 2-9710A Handset: stap 9, afbeelding 1 van 2 Disassembling General Electric Telephone 2-9710A Handset: stap 9, afbeelding 2 van 2
    • Slide the phone jack out from the shell by gently lifting up the female phone jack connector.

  10. Disassembling General Electric Telephone 2-9710A Handset: stap 10, afbeelding 1 van 1
    • Without removing the motherboard completely, pull up slightly and pivot the motherboard out of the shell.

    • Be careful not to pull the connectors out.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Alles Rebel

Lid sinds: 09/20/12

72 Reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 16-59, Forte Fall 2012 Lid van Cal Poly, Team 16-59, Forte Fall 2012

CPSU-FORTE-F12S16G59

4 Leden

17 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 7

Afgelopen 30 dagen: 22

Altijd: 2,678