Repareer je spullen Gemeenschap Winkel

Disassembling Compaq Mini 110 Heat Sink

Geschreven door: alea (en 5 andere bijdragers)
  • Reacties: 3
  • Favorieten: 5

Moeilijkheid

Zeer eenvoudig

Stappen

15

Tijd vereist

1 minuut

Secties

6

Markeringen

7

Needs Better Images

Heeft betere plaatjes nodig

Betere foto's zullen deze handleiding verbeteren. Help mee door het nemen, bewerken of uploaden van nieuwe foto's!

Student In Progress

Student in uitvoering

Hardwerkende studenten werken aan deze handleiding.

Missed a Step

Stap gemist

Oeps! Deze handleiding mist nu een paar belangrijke stappen.

Inconsistent Images

Inconsistente plaatjes

Deze handleiding zou veel cooler worden met foto's zoals het hoort (zie vereisten).

Action Shots

Actiemomenten

Wees een actieheld! Deze handleiding heeft plaatjes nodig die beter tonen hoe specifieke handelingen uitgevoerd moeten worden.

Bullets!

Opsommingstekens!

Betere coƶrdinatie met markeringen en kleur/type bullet points om deze handleiding nog duidelijker te maken!

Markup Mishap

Mislukte opmaak

Deze handleiding heeft een betere opmaak nodig. Help mee door het corrigeren van de opmaak of door aantekeningen te maken.

Inleiding

This little dude can get in your way, so move him out.

Gereedschap

Onderdelen

Geen onderdelen opgegeven.

  1. Locate the battery and the battery tabs on the bottom of the Compaq Mini. Locate the battery and the battery tabs on the bottom of the Compaq Mini.

    • Locate the battery and the battery tabs on the bottom of the Compaq Mini.

    Vertaal

  2. Push both tabs inward simultaneously and slide the battery out. Push both tabs inward simultaneously and slide the battery out. Push both tabs inward simultaneously and slide the battery out.

    • Push both tabs inward simultaneously and slide the battery out.

    Vertaal

  3. Use a Philips #0 Screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover. Use a Philips #0 Screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover.

    • Use a Philips #0 Screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover.

    Vertaal

  4. Push out the side tabs simultaneously and pull out the old RAM module. Insert the new module in the same place as the old module. Be sure to evenly insert 'gold pins' in the same orientation that the old module was removed.

    • Push out the side tabs simultaneously and pull out the old RAM module. Insert the new module in the same place as the old module. Be sure to evenly insert 'gold pins' in the same orientation that the old module was removed.

    • While sliding the module in, press side tabs in place.

    Vertaal

  5. Reinstall the cover and screws.

    • Reinstall the cover and screws.

    Vertaal

  7. Remove the rubber pads located on the corners of your Compaq Mini. There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

    • Remove the rubber pads located on the corners of your Compaq Mini.

    • There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

    Vertaal

  8. Unscrew all the corner screws. There are four total, one under each rubber pad. Unscrew all the corner screws. There are four total, one under each rubber pad.

    • Unscrew all the corner screws. There are four total, one under each rubber pad.

    Vertaal

  9. Unscrew the screw for the bottom case located in the RAM compartment. Unscrew the screw for the bottom case located in the RAM compartment.

    • Unscrew the screw for the bottom case located in the RAM compartment.

    Vertaal

  10. Remove the three screws in the silver tabs at the back of the keyboard. These are located at the back of the base under the screen.

    • Remove the three screws in the silver tabs at the back of the keyboard.

    • These are located at the back of the base under the screen.

    Vertaal

  11. Remove the three screws holding the panel in place.

    • Remove the three screws holding the panel in place.

    Vertaal

  12. Pull up on the tab to remove the plate. Pull up on the tab to remove the plate.

    • Pull up on the tab to remove the plate.

    Vertaal

  13. Unscrew the eight screws that are circled in the picture from the plastic top cover.

    • Unscrew the eight screws that are circled in the picture from the plastic top cover.

    Vertaal

  14. Pry up the top plastic cover using a spudger. The yellow rectangles show two tabs under the screen that need to be pushed in. The yellow rectangles show two tabs under the screen that need to be pushed in.

    • Pry up the top plastic cover using a spudger.

    • The yellow rectangles show two tabs under the screen that need to be pushed in.

    Vertaal

  15. Remove the cable by carefully pulling it up. Be careful when lifting up the cover because the track pad is still attached.

    • Remove the cable by carefully pulling it up.

    • Be careful when lifting up the cover because the track pad is still attached.

    Vertaal

  16. Remove all four screws. The underside has lubricant to help the heat sink do its job. Be careful not to smear it all over the place.

    • Remove all four screws.

    • The underside has lubricant to help the heat sink do its job. Be careful not to smear it all over the place.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 5 andere bijdragers

alea

Lid sinds: 06-10-10

1.381 Reputatie

14 handleidingen geschreven

Badges: 13

+10 andere badges

Team

Cal Poly, Team 22-2, Maness Fall 2010 Lid van Cal Poly, Team 22-2, Maness Fall 2010

CPSU-MANESS-F10S22G2

6 Leden

20 handleidingen geschreven

0 Opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 5

Altijd: 3,925