Repareer je spullen Gemeenschap Winkel

Canon Powershot SD880 Flash Replacement

Inleiding

This guide will provide you with the necessary direction to disassemble the flash on a Canon Powershot SD880. Before you start, know that the flash device has a few delicate connections and should be handled with care.

Wat je nodig hebt

  1. Canon Powershot SD880 Flash Replacement, Back Cover: stap 1, afbeelding 1 van 3 Canon Powershot SD880 Flash Replacement, Back Cover: stap 1, afbeelding 2 van 3 Canon Powershot SD880 Flash Replacement, Back Cover: stap 1, afbeelding 3 van 3

    • Remove the two 2.4 mm screws on the side of the camera that are next to the LCD screen using a Phillips #00 screwdriver.

    • Remove the two 4.1 mm screws on the other side using a Phillips #00 screwdriver.

    • One screw will be located under the rubber USB flap.

    • Remove the single 2.6 mm screw from the bottom of the camera using a Phillips #00 screwdriver.

    • Slowly pull the back cover off of the camera.

    Bewerken

  2. Canon Powershot SD880 Flash Replacement, Front Cover: stap 2, afbeelding 1 van 3 Canon Powershot SD880 Flash Replacement, Front Cover: stap 2, afbeelding 2 van 3 Canon Powershot SD880 Flash Replacement, Front Cover: stap 2, afbeelding 3 van 3

    • Remove the 2.6 mm screw from the bottom of the camera using a Phillips #00 screwdriver.

    • Remove the 4.1 mm screw from the menu button side of the camera using a Phillips #00 screwdriver.

    • The two screws on the other side of the camera were already removed when the back cover was taken off.

    Bewerken

  4. Canon Powershot SD880 Flash Replacement, Top Panel: stap 3, afbeelding 1 van 2 Canon Powershot SD880 Flash Replacement, Top Panel: stap 3, afbeelding 2 van 2

    • Unplug the green and white plugs that connect the top panel to the top of the logic board.

    • Dislodge the tab above the lens.

    • Dislodge the tab at the back.

    Bewerken

  5. Canon Powershot SD880 Flash Replacement, LCD Display: stap 4, afbeelding 1 van 3 Canon Powershot SD880 Flash Replacement, LCD Display: stap 4, afbeelding 2 van 3 Canon Powershot SD880 Flash Replacement, LCD Display: stap 4, afbeelding 3 van 3

    • Remove the two 2.9 mm screws at the top-right corner and bottom-left corner of the LCD screen using a Phillips #0 screwdriver.

    • Disconnect the ribbons that connect the screen to the camera.

    • Lift the screen off.

    Bewerken

  6. Canon Powershot SD880 Flash Replacement, Flash: stap 5, afbeelding 1 van 3 Canon Powershot SD880 Flash Replacement, Flash: stap 5, afbeelding 2 van 3 Canon Powershot SD880 Flash Replacement, Flash: stap 5, afbeelding 3 van 3

    • Use caution when removing the flash, as the capacitor may still have a charge.

    • Remove two 1.8 mm screws from the back using a Phillips #0 screwdriver to disconnect the metal guard.

    • To unplug the ribbon at the top of the camera, gently pull it from the plug-in point.

    • Disconnect the white plug from the red and black wires.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 9 andere bijdragers

Robert Manno

Lid sinds: 01/05/11

432 Reputatie

4 handleidingen geschreven

Medailles: 6

+3 andere badges

Team

Cal Poly, Team 13-3, Forte Winter 2011 Lid van Cal Poly, Team 13-3, Forte Winter 2011

CPSU-FORTE-W11S13G3

5 Leden

8 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 7

Altijd: 2,535