Ga door naar hoofdinhoud

Gereedschap

Onderdelen

Geen onderdelen opgegeven.

  1. Dis/assembling Eye/Pupil Camera Housing, Dis/assembling Eye/Pupil Camera Housing: stap 1, afbeelding 1 van 1
    • First: Eye Camera

    • Remove initial frame (crack off)

  2. Dis/assembling Eye/Pupil Camera Housing: stap 2, afbeelding 1 van 1
    • Remove 4 screws.

  3. Dis/assembling Eye/Pupil Camera Housing: stap 3, afbeelding 1 van 1
    • Remove cover to get to the PCB underneath

  4. Dis/assembling Eye/Pupil Camera Housing: stap 4, afbeelding 1 van 1
    • Remove two screws on the PCB.

  5. Dis/assembling Eye/Pupil Camera Housing: stap 5, afbeelding 1 van 1
    • Remove PCB from the base plastic piece.

  6. Dis/assembling Eye/Pupil Camera Housing: stap 6, afbeelding 1 van 1
    • Break base plastic piece. Cutters work well. Be careful not to snip the wire attached to the PCB.

  7. Dis/assembling Eye/Pupil Camera Housing: stap 7, afbeelding 1 van 1
    • Black mold (from 3D printer) piece attaches to the PCB with 4 screws.

  8. Dis/assembling Eye/Pupil Camera Housing: stap 8, afbeelding 1 van 1
    • Completed assembly of the eye camera.

  9. Dis/assembling Eye/Pupil Camera Housing, Pupil camera dis/assembly: stap 9, afbeelding 1 van 1
    • Back of pupil camera is glued on. Remove with flat-head.

  10. Dis/assembling Eye/Pupil Camera Housing: stap 10, afbeelding 1 van 1
    • Remove the black frame on the front of the pupil camera.

  11. Dis/assembling Eye/Pupil Camera Housing: stap 11, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 11, afbeelding 2 van 2
    • Once frame is taken off the front, two screws need to be removed.

  12. Dis/assembling Eye/Pupil Camera Housing: stap 12, afbeelding 1 van 1
    • One screw removed from the back.

  13. Dis/assembling Eye/Pupil Camera Housing: stap 13, afbeelding 1 van 1
    • Front housing comes off once the screws are removed from the frame.

    • Twist out the silver microphone.

  14. Dis/assembling Eye/Pupil Camera Housing: stap 14, afbeelding 1 van 1
    • Pull off bottom stand until it breaks off.

  15. Dis/assembling Eye/Pupil Camera Housing: stap 15, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 15, afbeelding 2 van 2
    • Remove rubber/plastic piece from the bottom

  16. Dis/assembling Eye/Pupil Camera Housing: stap 16, afbeelding 1 van 1
    • Remove four screws from under the plastic tape (removed from last step).

  17. Dis/assembling Eye/Pupil Camera Housing: stap 17, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 17, afbeelding 2 van 2
    • Bottom pops off

  18. Dis/assembling Eye/Pupil Camera Housing: stap 18, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 18, afbeelding 2 van 2
    • Separate the metal frame from the plastic assembly.

    • Avoid the cables

  19. Dis/assembling Eye/Pupil Camera Housing: stap 19, afbeelding 1 van 1
    • Take out PCB from the plastic housing.

  20. Dis/assembling Eye/Pupil Camera Housing: stap 20, afbeelding 1 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 20, afbeelding 2 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 20, afbeelding 3 van 3
    • Remove the rest of the black plastic housing.

  21. Dis/assembling Eye/Pupil Camera Housing: stap 21, afbeelding 1 van 1
    • Black plastic housing removed

  22. Dis/assembling Eye/Pupil Camera Housing: stap 22, afbeelding 1 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 22, afbeelding 2 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 22, afbeelding 3 van 3
    • Continue removing the black plastic housing surrounding the inner PCB.

  23. Dis/assembling Eye/Pupil Camera Housing: stap 23, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 23, afbeelding 2 van 2
    • PCB removed from the black plastic housing.

  24. Dis/assembling Eye/Pupil Camera Housing: stap 24, afbeelding 1 van 1
    • Autofocus assembly.

    • Remove two screws from the bottom of the auto-focus PCB.

  25. Dis/assembling Eye/Pupil Camera Housing: stap 25, afbeelding 1 van 1
    • Unscrew the lens

  26. Dis/assembling Eye/Pupil Camera Housing: stap 26, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 26, afbeelding 2 van 2
    • Take out the IR filter by using a scalpel for pulling out the lens tape.

  27. Dis/assembling Eye/Pupil Camera Housing: stap 27, afbeelding 1 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 27, afbeelding 2 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 27, afbeelding 3 van 3
    • Comparison photos of completed autofocus assembly vs in-progress autofocus assembly

  28. Dis/assembling Eye/Pupil Camera Housing: stap 28, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 28, afbeelding 2 van 2
    • IR LEDs replaced by SMD LED

    • Soldering required here (at bottom of LED to remove).

  29. Dis/assembling Eye/Pupil Camera Housing: stap 29, afbeelding 1 van 1
    • SMD LED info: Thick black line is near the positive side of the LED

    • Dark side (dot) is positive side on LED.

  30. Dis/assembling Eye/Pupil Camera Housing: stap 30, afbeelding 1 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 30, afbeelding 2 van 3 Dis/assembling Eye/Pupil Camera Housing: stap 30, afbeelding 3 van 3
    • Insert PCB into 3d-printed frame.

  31. Dis/assembling Eye/Pupil Camera Housing: stap 31, afbeelding 1 van 2 Dis/assembling Eye/Pupil Camera Housing: stap 31, afbeelding 2 van 2
    • Completed assembly.

    • Sugru used for nose/head rest

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Silas

Lid sinds: 25-11-13

291 Reputatie

1 Handleiding geschreven

0 Opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 1

Altijd: 624