Repareer je spullen Gemeenschap Winkel

DeWALT Hammer Drill DW511 Power Cord Replacement

Inleiding

Welcome to the Dewalt Hammer Drill DW511 power cord replacement guide. The power cord is an important part of the drill that delivers power to the device. You would want to replace the power cord because of a frayed or damaged cord. A common issue with a damaged power cord is the drill not running.

Caution should be taken when working with the power cord. It needs to be unplugged before working on any part of the drill.

Wat je nodig hebt

  1. DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: stap 1, afbeelding 1 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: stap 1, afbeelding 2 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: stap 1, afbeelding 3 van 3

    • Remove three 19 mm T20 Torx screws from the back of the drill.

    Vertaal

  2. DeWALT Hammer Drill DW511 Power Cord Replacement: stap 2, afbeelding 1 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 2, afbeelding 2 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 2, afbeelding 3 van 3

    • Place an opening tool in the groove line of the handle and pop the back loose.

    • Grab the drill with two hands and pull the cover off.

    Vertaal

  4. DeWALT Hammer Drill DW511 Power Cord Replacement, Power Cord: stap 3, afbeelding 1 van 2 DeWALT Hammer Drill DW511 Power Cord Replacement, Power Cord: stap 3, afbeelding 2 van 2

    • Firmly grab the body of the trigger.

    • Slowly pull the trigger until the entire body is out and only attached by wires.

    Vertaal

  5. DeWALT Hammer Drill DW511 Power Cord Replacement: stap 4, afbeelding 1 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 4, afbeelding 2 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 4, afbeelding 3 van 3
    Gereedschap gebruikt in deze stap:
    Tweezers
    $4.99
    Koop

    • With sharp point tweezers, push the little metal flap up in the hole holding the wire.

    • Clamp the wire with blunt tweezers, and slowly pull the wire out.

    Vertaal

  6. DeWALT Hammer Drill DW511 Power Cord Replacement: stap 5, afbeelding 1 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 5, afbeelding 2 van 3 DeWALT Hammer Drill DW511 Power Cord Replacement: stap 5, afbeelding 3 van 3

    • With a pair of blunt nose tweezers, grab the white wire.

    • Carefully wiggle the wire loose.

    • Pull the wire slowly until it comes out.

    Vertaal

  7. DeWALT Hammer Drill DW511 Power Cord Replacement: stap 6, afbeelding 1 van 1

    • With both wires free, the power cord is free from the trigger body.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 20

Altijd: 1,371