Inleiding

A guide on how to remove the Fan.

  1. Turn the laptop bottom side up with the rear panel facing forward.
    • Turn the laptop bottom side up with the rear panel facing forward.

    Voeg opmerking toe

  2. Remove the two T8 Torx screws that secure the LED cover to the base enclosure.
    • Remove the two T8 Torx screws that secure the LED cover to the base enclosure.

    Voeg opmerking toe

    • Turn the laptop top side up with the front facing forward. Open the screen.

    Voeg opmerking toe

    • Locate the F1 and F2 keys near the top left corner of the keyboard.

    Voeg opmerking toe

    • While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

    Voeg opmerking toe

    • Locate the Pause and Scroll keys near the top right corner of the keyboard.

    Voeg opmerking toe

    • While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

    Voeg opmerking toe

    • Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.

    Voeg opmerking toe

    • Lift the back edge of the keyboard and pull towards the screen.

    Voeg opmerking toe

    • Pull the cable and lift up to release.

    Voeg opmerking toe

  3. Verspreid de kerstsfeer
    Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12
    Verspreid de kerstsfeer
    Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12
    • Remove the keyboard.

    Voeg opmerking toe

    • Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.

    • Disconnect the cable connecting the fan to the system board.

    Voeg opmerking toe

    • Locate and remove the four screws in the copper plate.

    Voeg opmerking toe

    • Remove the heat spreader by pulling the whole assembly up out of the computer.

    Voeg opmerking toe

    • Flip the computer bottom side up with the rear facing forward.

    Voeg opmerking toe

    • Remove the six screws shown in picture.

    Voeg opmerking toe

    • Remove battery and then remove screw in metal support on case edge

    • Flip the computer top side up with the front facing you.

    Voeg opmerking toe

    • Lift up the palm rest from the front edge and swing it towards the screen.

    Voeg opmerking toe

    • Locate the first connector. Disconnect by firmly pulling up.

    Voeg opmerking toe

    • Locate the second connector. Remove by firmly pulling up.

    Voeg opmerking toe

    • Remove the palm rest.

    Voeg opmerking toe

    • Turn the base bottom side up.

    Voeg opmerking toe

    • Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.

    Voeg opmerking toe

    • Turn the base top side up with the front facing forward.

    Voeg opmerking toe

    • Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.

    Voeg opmerking toe

    • Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.

    • Disconnect the microphone cable from the system board.

    Voeg opmerking toe

    • Remove the top cover from the base.

    Voeg opmerking toe

    • Disconnect the fan cable from the system board.

    Voeg opmerking toe

    • Remove the fan from the base.

    Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Alex Hernandez

Lid sinds: 14-04-10

28 Reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 29-74, Johann Spring 2010 Lid van Cal Poly, Team 29-74, Johann Spring 2010

CPSU-JOHANN-S10S29G74

3 Leden

7 handleidingen geschreven

Remove battery FIRST before you do anything. Then remove all the screws on the back of the computer. The you can go to the front and follow all the steps afterward.

iam765 - Antwoord

Please DO NOT firmly remove any connectors. Most connectors have locks. In step 20 you can see the two different colors of the connector the bottom is black and the top (the lock) is brown. Each side of the lock sticks out further than the connector. One side at a time pull back on the lock. Connection should come out with no force. to reconnect, seat connection and push lock back in place. If any issues try unlocking and re-seat connection.

iam765 - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 3

Afgelopen 30 Dagen: 8

Altijd: 5,446