Onderdelen

Geen onderdelen nodig.

  • Hold the phone with the back (camera side) facing you. Slide the battery cover off of the phone.

Voeg opmerking toe

  • Pull the battery out by lifting the black tab on the left side of the battery.

Voeg opmerking toe

  • Remove the camera cover of the phone, using your light blue wedge tool.

Voeg opmerking toe

  • Unscrew the four black Torx head screws, found in each corner of the back.

  • Warning: Unscrewing the screw indicated in the picture will void any warranty on the phone.

Voeg opmerking toe

Unscrew the black Phillips head screw below the right speaker.
  • Unscrew the black Phillips head screw below the right speaker.

Voeg opmerking toe

  • After removing the screw, pull up on the motherboard to release it from the circuit board (green tab, see Figure 11). This will simply snap out, and does not require too much force.

Voeg opmerking toe

Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.
  • Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.

Voeg opmerking toe

Remove the four silver Phillips head screws from the screened half of the phone.
  • Remove the four silver Phillips head screws from the screened half of the phone.

Voeg opmerking toe

Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.
  • Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.

Voeg opmerking toe

Unscrew the four Phillips head screws that attach the screen to the front case.
  • Unscrew the four Phillips head screws that attach the screen to the front case.

Voeg opmerking toe

  • Remove the circuit board; pull it apart at the orange tab. This will detach the screen from its circuit board.

Voeg opmerking toe

Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.
  • Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.

Voeg opmerking toe

  • Place screen back into front cover.

Voeg opmerking toe

  • Screw the four smallest silver Torx head screws into the circuit board, which will attach it to the front cover.

Voeg opmerking toe

  • Feed the circuit board through the back piece.

Voeg opmerking toe

  • Use the four Phillips head silver screws to attach the back piece to the front of the phone.

Voeg opmerking toe

Slide the circuit board through the slot in the keyboard.
  • Slide the circuit board through the slot in the keyboard.

Voeg opmerking toe

  • Attach the keyboard to the sliding tracks using the four silver Torx screws.

Voeg opmerking toe

Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.
  • Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.

Voeg opmerking toe

Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.
  • Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.

Voeg opmerking toe

  • Place the back cover onto the motherboard, clicking it into place.

Voeg opmerking toe

Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.
  • Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.

Voeg opmerking toe

Replace the camera cover.
  • Replace the camera cover.

Voeg opmerking toe

Replace battery, keeping the black tab available to grab.
  • Replace battery, keeping the black tab available to grab.

Voeg opmerking toe

Slide the battery cover back into place.
  • Slide the battery cover back into place.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Laura Kimberly Simonds

Lid sinds: 24-09-12

301 Reputatie

3 handleidingen geschreven

Team

University of Maine, Team 1-1, Diaz Fall 2012 Lid van University of Maine, Team 1-1, Diaz Fall 2012

UMAINE-DIAZ-F12S1G1

4 Leden

3 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 2

Altijd: 353