Repareer je spullen Gemeenschap Winkel

Ceiva LF2003 Display Replacement

Inleiding

Replacing the display on this device is not very difficult. A couple sets of screws and wires are all that need removing, but don't rush or you might rip a cable.

Wat je nodig hebt

  1. Ceiva LF2003 Display Replacement, Exterior Frame and Matting: stap 1, afbeelding 1 van 1

    • Lay the device on its back, and rotate so the base is facing away from you.

    Bewerken

  2. Ceiva LF2003 Display Replacement: stap 2, afbeelding 1 van 1

    • Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.

    Bewerken

  3. Ceiva LF2003 Display Replacement: stap 3, afbeelding 1 van 1

    • Lift up the frame with your fingers and push down the rest of the device with your thumbs.

    Bewerken

  4. Ceiva LF2003 Display Replacement: stap 4, afbeelding 1 van 1

    • Remove the frame and matte from the device.

    Bewerken

  6. Ceiva LF2003 Display Replacement, Internal Plastic Screen Frame: stap 5, afbeelding 1 van 1

    • Remove the four 7mm Torx T6 screws.

    Bewerken

  7. Ceiva LF2003 Display Replacement: stap 6, afbeelding 1 van 2 Ceiva LF2003 Display Replacement: stap 6, afbeelding 2 van 2

    • Using the plastic opening tool or your fingers, lift up the frame from any edge.

    • Remove the frame from the device.

    Bewerken

  8. Ceiva LF2003 Display Replacement, Display: stap 7, afbeelding 1 van 3 Ceiva LF2003 Display Replacement, Display: stap 7, afbeelding 2 van 3 Ceiva LF2003 Display Replacement, Display: stap 7, afbeelding 3 van 3

    • Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board.

    • Alternate applying pressure to the left and right side of the connector to ensure that it does not break.

    Bewerken

  9. Ceiva LF2003 Display Replacement: stap 8, afbeelding 1 van 1

    • Remove the four 7mm Torx T6 screws.

    Bewerken

  10. Ceiva LF2003 Display Replacement: stap 9, afbeelding 1 van 2 Ceiva LF2003 Display Replacement: stap 9, afbeelding 2 van 2

    • Lift up the display from the left edge and flip display over.

    • Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.

    Bewerken

  11. Ceiva LF2003 Display Replacement: stap 10, afbeelding 1 van 3 Ceiva LF2003 Display Replacement: stap 10, afbeelding 2 van 3 Ceiva LF2003 Display Replacement: stap 10, afbeelding 3 van 3

    • Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector.

    • Once both pins are released, the ribbon cable should slide easily out.

    • It may be easier if someone else holds the display so the cable does not get ripped out.

    Bewerken

  12. Ceiva LF2003 Display Replacement: stap 11, afbeelding 1 van 1

    • Remove the display assembly from the device.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 2 andere bijdragers

Casey Glasgow

Lid sinds: 01/26/14

510 Reputatie

5 handleidingen geschreven

Medailles: 7

+4 andere badges

Team

Cal Poly, Team 9-25, Maness Winter 2014 Lid van Cal Poly, Team 9-25, Maness Winter 2014

CPSU-MANESS-W14S9G25

4 Leden

5 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 1

Altijd: 135