Inleiding

This guide is a step-by-step instruction on how to remove and replace a broken LCD screen for the Canon Powershot SD790 IS.

Tools Required: #00 Phillips-head screwdriver
  • Tools Required: #00 Phillips-head screwdriver

  • Caution: The six screws removed in this step are tiny and should be placed in a secure location.

  • Using the #00 Phillips-head screwdriver, remove the two screws from the left side (as shown in picture 1).

  • Using the #00 Phillips-head screwdriver, remove the two screws from the right side of the camera (as shown in picture 2).

  • Using the #00 Phillips-head screwdriver, remove the two screws from the bottom of the camera (as shown in picture 3).

Voeg opmerking toe

Using your fingers, manually pop open the USB cover, labeled as “A/V OUT DIGITAL.” This is located on the side of the camera (refer to picture).
  • Using your fingers, manually pop open the USB cover, labeled as “A/V OUT DIGITAL.” This is located on the side of the camera (refer to picture).

  • Gently pull the tab of the side cover and completely detach it from the camera.

Side cover may not be attached. If so, just skip step two.

Michaela Gergel - Antwoord

  • Tools Required: Spudger

  • To pry off the screen cover, gently grab the sides of the camera. If necessary, use spudger (refer to pictures).

  • Once the screen cover is removed, the front cover and side plate will slide off (refer to pictures).

Voeg opmerking toe

  • Tools required: #00 Phillips-head screwdriver

  • Caution: The three screws removed in this step are tiny and should be placed in a secure location.

  • Using the #00 Phillips-head screwdriver, remove the two screws located on the bottom of the camera, as well as the single screw located next to the LCD screen (refer to pictures).

Voeg opmerking toe

  • Tools Required: Tweezers

  • Using tweezers, gently slide the small, orange, translucent strip (LCD cable) horizontally from its white plug towards the camera's screen (refer to picture).

Voeg opmerking toe

  • Caution: Do not completely remove the button release panel from the camera. Black and red cables will keep the panel attached to the camera. Just let the panel hang out of the way as you complete the remaining steps.

  • Using your fingers, pop open the USB port cover (labeled as “A/V OUT DIGITAL” on the camera).

  • Using your fingers, remove the button release panel, located on the top of the camera (refer to picture).

Voeg opmerking toe

  • Tools Required: spudger

  • Caution: Gray clip is very small.

  • Note: To view a larger version of these pictures, click the "Use huge" option located in the upper lefthand corner of the picture.

  • Using the spudger, flip the small gray clip (located next to the dark gray LCD port on top of camera) in an upward motion. Clip should remain attached to camera, not removed completely (refer to pictures).

Voeg opmerking toe

  • Tools required: Tweezers

  • Using tweezers, gently slide the orange, translucent LCD ribbon from its dark gray plug horizontally towards the screen.

  • Once you have finished this step, the screen is now ready to be replaced.

Voeg opmerking toe

  • Note: This is the first step in reassembling the camera with your new LCD screen.

  • Slide the LCD screen back on the camera by aligning the bottom left flap with the outside of the screw hole (refer to picture). Check all corners of the screen to ensure proper fit.

Voeg opmerking toe

  • Tools Required: Tweezers

  • Insert LCD strip horizontally into port, using tweezers if necessary.

  • Flip small gray clip from the vertical position to the horizontal position. There will be a light clicking sound when the flap switches to the horiztonal position, locking the LCD strip in place.

Voeg opmerking toe

  • Take the white prong on the button panel (located on top of camera) and line up with the hole (as shown in picture). Once these are aligned, the button panel will snap into place.

Voeg opmerking toe

  • Tools Required: Tweezers

  • Caution: Use extreme care when completing this step.

  • On the bottom of the camera, horizontally slide the LCD ribbon back into its port, using tweezers if necessary.

Voeg opmerking toe

  • Tools required: #00 Phillips-head screwdriver

  • Caution: The three screws reattached in this step are tiny and should be handled carefully.

  • Note: the two screws on the bottom of the camera should be the longer screws, not the shorter ones.

  • Using the #00 Phillips-head screwdriver, reattach the two screws located on the bottom of the camera and the one screw on the side of the camera. These screws hold the LCD screen in place (refer to pictures).

Voeg opmerking toe

  • Note: Tabs for the front cover go on the outside

  • Starting with the side plate, line it up and snap it back into place on the camera.

  • Lining up the tabs on the outside of the camera, snap the front cover back into place.

  • Once the side plate and front cover are in place, the screen cover will snap back onto the camera.

Voeg opmerking toe

  • Note: The USB port, labeled "A/V DIGITAL OUT", must be open prior to reattaching the side cover.

  • Reattach the side cover of the camera by snapping it back into place (refer to picture). Once the side cover is in place, close the USB cover, labeled “A/V DIGITAL OUT.”

Voeg opmerking toe

  • Tools required: #00 Phillips-head screwdriver

  • Caution: The six screws used in this step are very tiny and should be handled carefully.

  • Using the #00 Phillips-head screwdriver, reattach the shorter screws on the left, right and bottom sides of the camera (refer to pictures).

Voeg opmerking toe

Eindstreep

2 andere personen hebben deze handleiding voltooid.

Gabriela

Lid sinds: 11-01-11

138 Reputatie

1 Handleiding geschreven

Team

Cal Poly, Team 4-33, Regan Winter 2011 Lid van Cal Poly, Team 4-33, Regan Winter 2011

CPSU-REGAN-W11S4G33

4 Leden

5 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 1

Altijd: 3,159