Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

Canon Powershot S200 Camera lens Replacement

Geschreven door: Joseph Melo (en 3 andere bijdragers)
  • Reacties: 1
  • Favorieten: 2

Moeilijkheid

Gemiddeld

Stappen

27

Tijd vereist

15 - 20 minuten

Secties

4

Markeringen

2

Needs Better Images

Heeft betere plaatjes nodig

Betere foto's zullen deze handleiding verbeteren. Help mee door het nemen, bewerken of uploaden van nieuwe foto's!

Bullets!

Opsommingstekens!

Betere coördinatie met markeringen en kleur/type bullet points om deze handleiding nog duidelijker te maken!

Inleiding

The lens is used for capturing specific scenes and to feed these scenes into the camera.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Slide grey latch to open the battery compartment. Slide grey latch to open the battery compartment.

    • Slide grey latch to open the battery compartment.

    Bewerken

  2. Push orange retaining clip to the right to free battery. Push orange retaining clip to the right to free battery.

    • Push orange retaining clip to the right to free battery.

    Bewerken

  3. Remove battery from the camera.

    • Remove battery from the camera.

    Bewerken

  4. Remove the lanyard.

    • Remove the lanyard.

    Bewerken

  5. Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

    • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

    • Be careful to keep track of the different screw sizes as you proceed with this guide.

    Bewerken

  6. Remove the single 3.8mm screw from the back face of the camera.

    • Remove the single 3.8mm screw from the back face of the camera.

    Bewerken

  7. Remove the two 2.3mm screws from the right face of the camera.

    • Remove the two 2.3mm screws from the right face of the camera.

    Bewerken

  8. Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

    • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

    Bewerken

  9. Pull the back face panel away from the front end of the body. This may take some wiggling and force.

    • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

    Bewerken

  10. iPhone Batterij Fix Kits

    Slechts $29.99

    Buy Now

    iPhone Batterij Fix Kits

    Slechts $29.99

    Buy Now

  11. Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.

    • Remove the CF card door from the left side of the camera body.

    Bewerken

  12. Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate. Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

    • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

    Bewerken

  13. Remove the front face by sliding it off.

    • Remove the front face by sliding it off.

    Bewerken

  14. Remove the rubber seal that goes over the right side of the viewfinder.

    • Remove the rubber seal that goes over the right side of the viewfinder.

    Bewerken

  15. Remove the two 3.9mm screws that retain the laminated cooper sheet.

    • Remove the two 3.9mm screws that retain the laminated cooper sheet.

    Bewerken

  16. Remove the seven wire connections that connect to the motherboard. Remove the seven wire connections that connect to the motherboard.

    • Remove the seven wire connections that connect to the motherboard.

    Bewerken

  17. Remove the single 3.8mm screw that is on the motherboard.

    • Remove the single 3.8mm screw that is on the motherboard.

    Bewerken

  18. Carefully remove the motherboard from the main frame of the camera body.

    • Carefully remove the motherboard from the main frame of the camera body.

    Bewerken

  19. After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

    • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

    Bewerken

  20. Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

    • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

    Bewerken

  21. Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

    Bewerken

  22. Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

    • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

    Bewerken

  23. Unsolder the four points at the top of the screen with a soldering iron

    • Unsolder the four points at the top of the screen with a soldering iron

    Bewerken

    • You do not need to unsolder the screen to get to the lens, but follow the rest of the steps to free the screen from the housing plate.

    Bewerken

  25. Remove the card-reader shield by removing the screw at the top of the shield.

    • Remove the card-reader shield by removing the screw at the top of the shield.

    Bewerken

  26. Remove the 2 black screws that attach the battery box to the housing plate. The second picture shows the battery box detached from the housing plate.

    • Remove the 2 black screws that attach the battery box to the housing plate.

    • The second picture shows the battery box detached from the housing plate.

    Bewerken

  27. Remove the three (3.1mm) black screws that were behind the screen and battery box.

    • Remove the three (3.1mm) black screws that were behind the screen and battery box.

    Bewerken

  28. Carefully remove the lens. Remove the bottom side of the lens first before the viewfinder side.

    • Carefully remove the lens.

    • Remove the bottom side of the lens first before the viewfinder side.

    • Be careful of wires and delicate parts.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 3 andere bijdragers

Joseph Melo

Lid sinds: 07-04-11

111 Reputatie

1 Handleiding geschreven

Badges: 3

Team

Cal Poly, Team 20-70, Walters Spring 2011 Lid van Cal Poly, Team 20-70, Walters Spring 2011

CPSU-WALTERS-S11S20G70

5 Leden

4 handleidingen geschreven

Één commentaar

Een opmerking toevoegen

Camera in the pictures is not Canon Powershot S200

jkovalai - Antwoord

Voeg opmerking toe

1024

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 3

Afgelopen 30 Dagen: 5

Altijd: 1,460