Ga door naar hoofdinhoud

Canon PowerShot SX120 IS Back Cover Replacement

Wat je nodig hebt

  1. Canon PowerShot SX120 IS Back Cover Replacement, Back Cover: stap 1, afbeelding 1 van 1
    • Turning the camera so the screen is facing you.

    • Remove the two black 3.4 mm screws with a Phillips #00 screwdriver.

  2. Canon PowerShot SX120 IS Back Cover Replacement: stap 2, afbeelding 1 van 1
    • Put the camera with the lens facing up and turn it to the side so the DC IN A/V OUT DIGITAL is facing you.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  3. Canon PowerShot SX120 IS Back Cover Replacement: stap 3, afbeelding 1 van 2 Canon PowerShot SX120 IS Back Cover Replacement: stap 3, afbeelding 2 van 2
    • Put the camera with the lens facing up, and turn it to the side where the battery cover is located.

    • Remove the three black 3.4 mm screws with a Phillips #00 screwdriver.

  4. Canon PowerShot SX120 IS Back Cover Replacement: stap 4, afbeelding 1 van 2 Canon PowerShot SX120 IS Back Cover Replacement: stap 4, afbeelding 2 van 2
    • Put the camera with the lens facing up, turn it to the side where the compartment of the battery (CR1220) for time/date is located.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  5. Canon PowerShot SX120 IS Back Cover Replacement: stap 5, afbeelding 1 van 1
    • Put the camera with the lens facing down, and turn it to the side where the DC IN A/V OUT DIGITAL cover and the silver lanyard attachment are located.

    • Open the DC IN A/V OUT DIGITAL cover.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  6. Canon PowerShot SX120 IS Back Cover Replacement: stap 6, afbeelding 1 van 3 Canon PowerShot SX120 IS Back Cover Replacement: stap 6, afbeelding 2 van 3 Canon PowerShot SX120 IS Back Cover Replacement: stap 6, afbeelding 3 van 3
    • Turn the camera with the lens facing down.

    • Opening the camera can be challenging. Don't get discouraged if it takes you a few tries before the camera is opened.

    • Use the iFixit opening tool to make leverage. Insert the opening tool in the seam where the front case and the back case assemble.

    • Carefully put pressure on the opening tool so the cover can gradually open.

    • Slowly slide the opening tool along the gap and around the edge of the camera.

    • When you are dissembling the back cover, the DC IN A/V OUT DIGITAL cover will also disassemble and fall off.

  7. Canon PowerShot SX120 IS Back Cover Replacement: stap 7, afbeelding 1 van 1
    • Remove the back cover and the DC IN A/V OUT DIGITAL cover from the camera.

Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Maria

Lid sinds: 03/13/14

875 Reputatie

1 Handleiding geschreven

Team

Één opmerking

It took me 2 hours to install the battery door. I dropped one screw and could not find it any more it just vanished.

I was lucky to find one just like the one I lost after a half hour search.All in all I did a pretty good good job for an

auto mechanic .Thanks very much for your help, it was very easy to follow your instructions.

Fred Czarnik

Frederick Czarnik - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 11

Altijd: 1,689