Inleiding

The LCD screen of the Canon PowerShot S80 is necessary for the normal operation of the camera. The screen is also vulnerable to cracks, chips and water damage. This guide will walk you through replacing your LCD screen and saving your camera.

Onderdelen

Geen onderdelen nodig.

Remove the knot on the wrist lanyard. Remove the battery and memory card.
  • Remove the knot on the wrist lanyard.

  • Remove the battery and memory card.

Voeg opmerking toe

Remove all screws from sides of outer casing. Begin removing the screws on the bottom of the outer casing.
  • Remove all screws from sides of outer casing.

  • Begin removing the screws on the bottom of the outer casing.

  • Remove the rest of the screws from the outer casing.

Voeg opmerking toe

Mac RAM Kits
Versnel je Mac. Breid zijn geheugen uit.
Mac RAM Kits
Haal meer megabytes uit je Mac.
Gently pull the front cover off the camera. Gently pull the front cover off the camera. Gently pull the front cover off the camera.
  • Gently pull the front cover off the camera.

Voeg opmerking toe

Open the "A/V Out Digital" cover slide, and remove the screw inside. Gently pull off the back casing. Remove the black "L" shaped piece of metal.
  • Open the "A/V Out Digital" cover slide, and remove the screw inside.

  • Gently pull off the back casing.

  • Remove the black "L" shaped piece of metal.

Voeg opmerking toe

Remove the three screws that are holding the screen in place and free the screen from the underlying components.
  • Remove the three screws that are holding the screen in place and free the screen from the underlying components.

  • Be careful of the ribbon wire that is still attached on the left of the screen.

Voeg opmerking toe

With the spudger, gently lift the black flap that is holding the wide ribbon cable wire in place. Unplug the wide ribbon cable.
  • With the spudger, gently lift the black flap that is holding the wide ribbon cable wire in place.

  • Unplug the wide ribbon cable.

  • Unplug the narrow ribbon cable to free the LCD screen from the camera body

The author failed to mention a couple things. First, the screen is in a holder which you remove, then after pulling off some electrical tape, you have to yank the actual screen out. Second, I only had two screws to pull the screen holder out, not three. Third, the thing that you have to pull to get the screen ribbon cable out is actually a tiny black hinge, so don't worry if it suddenly snaps back. Finally, to put the thing back together, it really helps if you have a tweezers to get the ribbon cables back into place.

and fyi replacement screens available from canon parts department for about 50 bucks.

steven - Antwoord

Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

BrettH

Lid sinds: 28-10-09

219 Reputatie

5 handleidingen geschreven

Team

Cal Poly, Team 19-5, Maness SU 2012 Lid van Cal Poly, Team 19-5, Maness SU 2012

CPSU-MANESS-SU12S19G5

1 Lid

5 handleidingen geschreven

Één commentaar

I presume the narrow ribbon cable supplies power to the backlight behind the screen? I replaced the combined screen and backlight assembly. I now have an image but it is extremely dark, barely visible. Perhaps the backlight didn't come on?

The contacts on both the wide ribbon and the narrow ribbon were corroded, probably the source of the problem.

Any suggestions?

Clive Williams - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 2

Altijd: 6,834