Inleiding

This is a guide to removing the camera's logic board.

Unscrew five Phillips screws using a #0 Phillips screwdriver.
  • Unscrew five Phillips screws using a #0 Phillips screwdriver.

  • One screw is on upper right corner of the back panel.

  • The other four screws are on the bottom of the camera.

Voeg opmerking toe

Open memory card cover by moving the slide switch toward the top end of of the camera.
  • Open memory card cover by moving the slide switch toward the top end of of the camera.

  • Remove the memory card from the slot.

Voeg opmerking toe

  • Remove the rear cover from the rest of the camera.

  • This may require gentle rocking of the case to free it.

Voeg opmerking toe

  • Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

Voeg opmerking toe

  • Free the front cover from the rest of the camera.

  • The cover may require gentle rocking to remove.

Voeg opmerking toe

  • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

Voeg opmerking toe

  • Gently separate the top of LCD from the rest of the camera using your thumb.

  • Be careful not pull the LCD too far because of the ribbon cable connection.

  • Place the Spudger in the hole of the electrical ribbon.

  • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

  • The LCD will still be connected to the rest of the camera

Voeg opmerking toe

  • Unscrew single Phillips screw with a #0 Phillips screwdriver.

  • Free the bottom panel and attached ribbon from the rest of the camera.

  • Be careful not to damage the ribbon.

Voeg opmerking toe

  • Turn over the camera.

  • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

  • The plastic will still be connected on the left side.

Voeg opmerking toe

  • Place the Spudger between the orange ribbon and the black ribbon gate.

  • Lift the ribbon gate using the Spudger.

Voeg opmerking toe

  • Place the Spludger in the corner of the ribbon above the hole.

  • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

Voeg opmerking toe

  • Free this ribbon and the bottom panel from the rest of the camera.

  • Be careful not to damage the ribbon.

Voeg opmerking toe

  • Turn the camera over so you can see the LCD.

  • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

Voeg opmerking toe

  • Lift the blue ribbon gate using the Spudger.

Voeg opmerking toe

  • Insert the Spudger into the hole of the ribbon.

  • Move the Spudger away from the gate to fully remove ribbon.

  • Be careful not to damage the ribbon.

Voeg opmerking toe

  • Lift the LCD away from the rest of the camera.

Voeg opmerking toe

  • Lift off the capture button by wiggling it back and forth while pulling upward.

  • Be careful not to damage the two clips.

Voeg opmerking toe

  • Flip open the four ribbon gates using the Spudger.

  • Gently pull out the ribbon cables from the gates using the Spudger.

Voeg opmerking toe

  • Unscrew the four Phillips screws using a #0 Phillips screwdriver.

Voeg opmerking toe

  • Gently lift the the logic board.

  • Be careful not to pull too hard and damage the white ribbon cable.

  • Place the Spudger so that it is between the logic board, the white ribbon cable, and the rest of the camera.

  • Remove the white ribbon cable by pulling the Spudger away from the camera, keeping it parallel to the logic board.

Voeg opmerking toe

  • Lay the logic board back down so that it is resting on the body of the camera.

  • Pull the two plugs (white and green) out to the right from the logic board using the tweezers.

Voeg opmerking toe

  • We're now ready to begin the desoldering process. You'll need a soldering iron, solder, and desoldering wick. You should be able to find these items at a Radio Shack if you don't already have them.

  • Please do not perform this step if you are not comfortable or have previous experience with soldering. Doing so, could cause severe damage to your camera.

  • Desolder the two soldered ribbon cables attached to the logic board.

Voeg opmerking toe

  • Free the logic board from the rest of the camera.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Nathan Balcom

Lid sinds: 21-01-10

81 Reputatie

8 handleidingen geschreven

Team

Cal Poly, Team 16-28, Maness Winter 2010 Lid van Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 Leden

9 handleidingen geschreven

Één commentaar

How brilliant! Great pictures! But where did you buy the new logic board?

Rosario - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 1

Altijd: 2,616