Inleiding

This guide illustrates how to replace the motherboard in the S400.

Unless stated otherwise, use a Phillips #00 screwdriver to remove all screws. On the backside of the camera, remove the 4.75 mm screw that sits at the top right corner.
  • Unless stated otherwise, use a Phillips #00 screwdriver to remove all screws.

  • On the backside of the camera, remove the 4.75 mm screw that sits at the top right corner.

  • Remove the four 4.75 mm screws that sit at the bottom of the camera.

Voeg opmerking toe

On the side of the camera, remove the two 4.75 mm screws that sit near the USB digital terminal.
  • On the side of the camera, remove the two 4.75 mm screws that sit near the USB digital terminal.

Voeg opmerking toe

On the side of the camera, remove the four 4.75 mm screws that sit near the wrist strap mount. Remove the two small metal plates, which the four screws held in place. Remove the two small metal plates, which the four screws held in place.
  • On the side of the camera, remove the four 4.75 mm screws that sit near the wrist strap mount.

  • Remove the two small metal plates, which the four screws held in place.

Remove the two small metal plates, which the four screws hold in place.

Mel Moss - Antwoord

When removing the casing, do not drop the small black plastic piece. This piece sits in a small gap above the lens, to the left of the flash, and underneath the camera case. Remove the small black plastic piece and set it aside.
  • When removing the casing, do not drop the small black plastic piece. This piece sits in a small gap above the lens, to the left of the flash, and underneath the camera case.

  • Remove the small black plastic piece and set it aside.

  • If necessary, use tweezers to remove the small black plastic piece.

  • Detach the front case and back case.

Suggest adding an image to show which piece the guide is referring to. It is difficult to understand without the camera.

Change the following directions to: "If necessary, use a tweezers to carefully remove the small black plastic piece."

Mel Moss - Antwoord

Do not remove the metal plate this step refers to. Removal at this step may damage the ribbon cable. Wait until the next step to remove the plate.
  • Do not remove the metal plate this step refers to. Removal at this step may damage the ribbon cable. Wait until the next step to remove the plate.

  • Remove the 3.5 mm screw that sits on the metal plate at the bottom of the camera.

  • Remove the two other 3.5 mm screws that sit on the side, to the left of the screw you just removed.

  • In the image, we have already removed some of the screws.

Voeg opmerking toe

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
A ribbon cable attaches to the metal plate and to the main circuit board, on the front of the camera. Gently release the black latch. Remove the ribbon cable and metal plate assembly.
  • A ribbon cable attaches to the metal plate and to the main circuit board, on the front of the camera.

  • Gently release the black latch.

  • Remove the ribbon cable and metal plate assembly.

Voeg opmerking toe

On the backside of the camera, remove the 3.5 mm screw that sits to the left of the viewfinder and above the LCD screen. Remove the second 3.5 mm screw that sits directly above the LCD screen.
  • On the backside of the camera, remove the 3.5 mm screw that sits to the left of the viewfinder and above the LCD screen.

  • Remove the second 3.5 mm screw that sits directly above the LCD screen.

  • Gently detach the ribbon cable.

Voeg opmerking toe

Locate the ribbon cable on the main circuit board, which sits below the lens.
  • Locate the ribbon cable on the main circuit board, which sits below the lens.

  • Gently release the black latch on the ribbon cable connector and detach the ribbon cable.

Voeg opmerking toe

Remove the LCD screen and set it aside. Remove the LCD screen and set it aside.
  • Remove the LCD screen and set it aside.

Voeg opmerking toe

On the main circuit board, gently release the black latches of the four ribbon cables.
  • On the main circuit board, gently release the black latches of the four ribbon cables.

  • Gently detach the ribbon cables.

Voeg opmerking toe

Detach the white-capped and green-capped wires, which sit near the flash. Detach the white-capped and green-capped wires, which sit near the flash.
  • Detach the white-capped and green-capped wires, which sit near the flash.

Voeg opmerking toe

Using a spudger, gently detach the shutter button assembly from the camera.
  • Using a spudger, gently detach the shutter button assembly from the camera.

Voeg opmerking toe

Remove the four 3.5 mm screws that hold the main circuit board.
  • Remove the four 3.5 mm screws that hold the main circuit board.

  • In the image, we have already removed some of the screws.

  • Do not remove the main circuit board yet.

Voeg opmerking toe

Do not completely remove the main circuit board from the camera. A soldered ribbon cable still attaches the board to the camera. Complete removal would break the soldering points. In a hinge-like motion, gently lift the bottom of the main circuit board, which is the side without the soldering points.
  • Do not completely remove the main circuit board from the camera. A soldered ribbon cable still attaches the board to the camera. Complete removal would break the soldering points.

  • In a hinge-like motion, gently lift the bottom of the main circuit board, which is the side without the soldering points.

  • Gently detach the white ribbon cable from the underside of the main circuit board.

Voeg opmerking toe

Do not attempt this next step unless you have soldering experience and feel comfortable desoldering. Otherwise you may damage the camera. Gently desolder the two ribbon cables attached to the motherboard.
  • Do not attempt this next step unless you have soldering experience and feel comfortable desoldering. Otherwise you may damage the camera.

  • Gently desolder the two ribbon cables attached to the motherboard.

  • Remove the motherboard.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Ross Bryan

Lid sinds: 21-01-11

350 Reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 5-19, Amido Winter 2011 Lid van Cal Poly, Team 5-19, Amido Winter 2011

CPSU-AMIDO-W11S5G19

4 Leden

6 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 1

Altijd: 2,706