Inleiding

Use this guide to replace or repair your speaker.

Onderdelen

Geen onderdelen nodig.

Orient the camera so that the viewfinder is on your left and the lens is on your right.
  • Orient the camera so that the viewfinder is on your left and the lens is on your right.

  • Remove the 4mm #00 Phillips screw.

Voeg opmerking toe

Reorient the camera with the back button pad and viewfinder towards you.
  • Reorient the camera with the back button pad and viewfinder towards you.

  • Remove the three 4mm #00 Phillips screws shown on the rear face of camcorder.

Voeg opmerking toe

  • Remove the plastic cover from the rear of the camcorder by gently pulling it towards you while holding the camera as shown.

  • The Battery Should be removed at this point, please ignore it in the picture.

Voeg opmerking toe

  • Remove the 4mm #00 Phillips screw located to the right of the LCD release switch.

Voeg opmerking toe

  • Open the LCD by using the release switch.

  • Reorient the camera with the playback button pad and edge of LCD screen facing you.

  • Remove the 4mm #00 Phillips screw shown.

Voeg opmerking toe

  • Reorient the camera with the top facing you. The side with the LCD screen should be on the right and the other side panel should be on the right.

  • Open the pop up flash on the top of the camcorder.

  • A loud clicking noise is expected.

  • Remove the 4mm #00 Phillips screw shown.

Voeg opmerking toe

  • Reorient the camera with the bottom facing you, LCD screen on the right, side panel on the left.

  • Open the tape deck by sliding the switch and moving the deck cover to the left as shown.

Voeg opmerking toe

  • Remove 4mm #00 Phillips screw.

Voeg opmerking toe

  • Reorient camera with lens facing you.

  • Remove the #00 Philips 4mm screw shown on the hinge of the tape deck cover.

Voeg opmerking toe

  • To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you.

Voeg opmerking toe

  • Close the tape deck by gently pushing it toward the body of the camera.

  • Slide and remove the plastic cover on the bottom right, exposing the interface shown.

Voeg opmerking toe

  • Gently pull the front plastic cover towards you to remove.

Voeg opmerking toe

  • Remove 2 Philips #00 4mm screw shown.

Voeg opmerking toe

  • Reorient the camera so you are looking at the side of the camera with the viewfinder on the left and lens on the right.

  • Holding the camera as shown,remove the 4mm #00 Phillips screw.

Voeg opmerking toe

  • Remove the 4 Philips #00 4mm screws shown.

Voeg opmerking toe

  • Reorient the camera with the lens facing you.

  • Gently pull the side panel of the camera to the right to remove.

  • Be aware that that there are wires connecting the cover to the body of the device, so the side cover will not come off entirely.

Voeg opmerking toe

  • The side of the device should now be open as shown. Again, there are wire connections between the side cover and the body of the camcorder. Do not separate the two entirely!

Voeg opmerking toe

  • Remove the screw above the speaker's housing.

Voeg opmerking toe

  • Remove the small battery with the "Caution" on it.

Voeg opmerking toe

  • Remove the screw from inside the battery housing.

Voeg opmerking toe

  • Remove the 3 screws holding the metal piece over the speaker.

Voeg opmerking toe

  • Lift up and remove the metal cover.

Voeg opmerking toe

  • Lift and remove the speaker.

Voeg opmerking toe

  • Replace the broken speaker with a new one.

  • The speaker's wires need to be desoldered.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Jeanette Neethling

Lid sinds: 19-01-11

531 Reputatie

5 handleidingen geschreven

Team

Cal Poly, Team 1-12, Amido Winter 2011 Lid van Cal Poly, Team 1-12, Amido Winter 2011

CPSU-AMIDO-W11S1G12

4 Leden

6 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 0

Altijd: 589