Inleiding

This fix is safe and only requires a screwdriver.

Onderdelen

Geen onderdelen nodig.

Remove the two 4.8 mm black screws above the lens on the front of the camera.
  • Remove the two 4.8 mm black screws above the lens on the front of the camera.

Voeg opmerking toe

Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.
  • Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.

Voeg opmerking toe

Remove the 4.8 mm black screw on the left side of the camera.
  • Remove the 4.8 mm black screw on the left side of the camera.

Voeg opmerking toe

Remove the front panel by lifting it away from the camera's body.
  • Remove the front panel by lifting it away from the camera's body.

Voeg opmerking toe

Remove seven 4.25 mm black screws on the bottom panel.
  • Remove seven 4.25 mm black screws on the bottom panel.

Voeg opmerking toe

Remove the bottom panel.
  • Remove the bottom panel.

Voeg opmerking toe

Remove two 6.5 mm black screws from the panel.
  • Remove two 6.5 mm black screws from the panel.

Voeg opmerking toe

Remove the plastic remote control socket cap by pulling it straight out.
  • Remove the plastic remote control socket cap by pulling it straight out.

Voeg opmerking toe

Slide panel toward bottom of camera to remove. Slide panel toward bottom of camera to remove.
  • Slide panel toward bottom of camera to remove.

Voeg opmerking toe

Slide the outer eyepiece upward to remove it.
  • Slide the outer eyepiece upward to remove it.

Voeg opmerking toe

Remove the two 4.75 mm black screws located  on the top of the camera.
  • Remove the two 4.75 mm black screws located on the top of the camera.

Voeg opmerking toe

Remove the four 4.3 mm  black screws near the bottom corners of the eyepiece at the back of the camera.
  • Remove the four 4.3 mm black screws near the bottom corners of the eyepiece at the back of the camera.

Voeg opmerking toe

Slowly separate the top panel from the camera by pushing it upward. Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.
  • Slowly separate the top panel from the camera by pushing it upward.

  • Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.

Voeg opmerking toe

Remove the two 5.5 mm screws from front of camera.
  • Remove the two 5.5 mm screws from front of camera.

Voeg opmerking toe

Remove grip panel.
  • Remove grip panel.

Voeg opmerking toe

Remove one black screw from battery door on underside of grip.
  • Remove one black screw from battery door on underside of grip.

Voeg opmerking toe

Remove battery door.
  • Remove battery door.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Jackie

Lid sinds: 17-04-11

218 reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 8-8, Regan Spring 2011 Lid van Cal Poly, Team 8-8, Regan Spring 2011

CPSU-REGAN-S11S8G8

5 Leden

11 handleidingen geschreven

Één commentaar

I was able to complete this by going from step 9 to 15. Oddly, I only had one screw to remove in step 15 but the grip piece easily slid out without needing to remove the top of the camera.

Alan - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 4

Afgelopen 30 Dagen: 13

Altijd: 3,078