Inleiding

This guide was written to aid with Blackberry Curve screen replacement. Following the steps below should provide relatively simple means of achieving this goal.

  1. Place your Blackberry face down in front of you.
    • Place your Blackberry face down in front of you.

  2. Locate the indent on the bottom of the back cover.
    • Locate the indent on the bottom of the back cover.

    • Use your fingernail to lift and remove the back cover.

  3. From the top, use your fingernail to lift and remove the battery.
    • From the top, use your fingernail to lift and remove the battery.

  4. Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
    • Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.

  5. Place the phone face up and use tweezers to securely grip and lift the screen upwards. Place the phone face up and use tweezers to securely grip and lift the screen upwards.
    • Place the phone face up and use tweezers to securely grip and lift the screen upwards.

  6. Gratis verzending van alle bestellingen van meer dan US$ 100,00 of met een Pro Tech Toolkit!

    Doorblader onze winkel

    Ooit iets gerepareerd? Je bent een genie.

    Deel je reparatie met #ImAGenius

    We zijn allemaal genieën

    Deel je reparatie met #ImAGenius

  7. Use a plastic opening tool to lift the bottom edge of the front cover.
    • Use a plastic opening tool to lift the bottom edge of the front cover.

  8. Use your nails to unclip the sides of the frame from the phone.
    • Use your nails to unclip the sides of the frame from the phone.

  9. Lift and remove the frame.
    • Lift and remove the frame.

  10. Lift and remove the keyboard.
    • Lift and remove the keyboard.

  11. Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver
    • Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver

  12. Carefully pull the keyboard base up and away from the phone.
    • Carefully pull the keyboard base up and away from the phone.

    • Disconnect the keyboard base from the phone completely.

  13. Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver
    • Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver

  14. Use a plastic opening tool to find the crease below the screen. Insert where shown and use the tool to unclip the two sides of screen from body.
    • Use a plastic opening tool to find the crease below the screen.

    • Insert where shown and use the tool to unclip the two sides of screen from body.

      • The opening tool goes approximately midway between the top and bottom edge of the screen.

  15. From the back of the phone, use a finger to push the front piece of the phone away from the back piece. From the back of the phone, use a finger to push the front piece of the phone away from the back piece.
    • From the back of the phone, use a finger to push the front piece of the phone away from the back piece.

  16. Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard. Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard. Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard.
    • Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard.

Conclusie

To reassemble your device, follow these instructions in reverse order.

8 andere personen hebben deze handleiding voltooid.

Alek Squires

Lid sinds: 30-09-13

419 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team 14-7, Forte Fall 2013 Lid van Cal Poly, Team 14-7, Forte Fall 2013

CPSU-FORTE-F13S14G7

5 Leden

5 handleidingen geschreven

Één commentaar

would appreciate new ldc part # and order info! - - !

Donald Burgo - Antwoord

Weergavestatistieken:

Afgelopen 24 Uren: 1

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 22

Altijd: 3,991