Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Winkel

Inleiding

This guide will demonstrate the steps needed to disconnect and replace the Power Button Circuit Board in the Acer AL1714. A malfunction in this part can cause possible issues with the ability to turn your device on.

  1. Turn the monitor facedown. Unscrew the 5 screws holding the back cover on.
    • Turn the monitor facedown.

    • Unscrew the 5 screws holding the back cover on.

    • (This may require flipping the monitor over and shaking the screws loose once they're already unscrewed)

  2. Take the edge tool or a metal ruler and insert it into the bezel. Apply pressure and push down. Do the same to the right side.
    • Take the edge tool or a metal ruler and insert it into the bezel.

    • Apply pressure and push down.

    • Do the same to the right side.

    • Once the side of bezel facing you is decoupled, take the back cover and pry it loose.

  3. Remove the Flat Flex Cable from the Power Supply Board under the metal cover. Pull the cord back and out of the way. (It may be stuck down with adhesive)
    • Remove the Flat Flex Cable from the Power Supply Board under the metal cover.

    • Pull the cord back and out of the way.

    • (It may be stuck down with adhesive)

  4. Unscrew the cord anchors for the VGA port. (Use needle nose pliers if they're too tight for removal by hand) (Use needle nose pliers if they're too tight for removal by hand)
    • Unscrew the cord anchors for the VGA port.

    • (Use needle nose pliers if they're too tight for removal by hand)

  5. Turn the monitor around. Unscrew the 1 screw holding the Flex Power Cable cover.
    • Turn the monitor around.

    • Unscrew the 1 screw holding the Flex Power Cable cover.

    • Lift up and remove the Flex Power Cable cover.

    • (Careful: This may be sharp)

  6. Unscrew the 5 screws holding the metal cage on.
    • Unscrew the 5 screws holding the metal cage on.

  7. SLA DE UPGRADE OVER

    Bespaar door het te repareren met een alles-in-één kit.

    Koop iPhone-reparatiekits

    SLA DE UPGRADE OVER

    Bespaar door het te repareren met een alles-in-één kit.

    Koop iPhone-reparatiekits
  8. Turn the monitor around. Lift up on the back of the metal cage slightly.
    • Turn the monitor around.

    • Lift up on the back of the metal cage slightly.

    • Pull the cage toward self.

    • (Must be careful to free the cover of the VGA port and power supply input)

  9. Lift up on the Flat Flex Cable holder tabs to release cords. Lift up on the Flat Flex Cables and bend them out of the working area. Lift up on the Flat Flex Cables and bend them out of the working area.
    • Lift up on the Flat Flex Cable holder tabs to release cords.

    • Lift up on the Flat Flex Cables and bend them out of the working area.

  10. Unplug the 4 backlight wires from their ports on the Power Supply Board. (Considering their size, the best way to unplug the backlight wires is by slowly jiggling wires out of place) (Considering their size, the best way to unplug the backlight wires is by slowly jiggling wires out of place)
    • Unplug the 4 backlight wires from their ports on the Power Supply Board.

    • (Considering their size, the best way to unplug the backlight wires is by slowly jiggling wires out of place)

  11. Unscrew the 5 screws holding the Power Supply Board and Video Display boards on.
    • Unscrew the 5 screws holding the Power Supply Board and Video Display boards on.

  12. Lift up and remove the joined Power Supply Board and Video Display boards. Lift up and remove the joined Power Supply Board and Video Display boards.
    • Lift up and remove the joined Power Supply Board and Video Display boards.

  13. Carefully detach the Power Supply and Video Display boards at their connector joint. (This step is not necessary for the removal and replacement of the Power Button Circuit board) (This is only a precaution so as not to bend or break the connector joint between the two boards)
    • Carefully detach the Power Supply and Video Display boards at their connector joint.

    • (This step is not necessary for the removal and replacement of the Power Button Circuit board)

    • (This is only a precaution so as not to bend or break the connector joint between the two boards)

  14. Remove the Flat Flex Cable from the Power Button Circuit Board.
    • Remove the Flat Flex Cable from the Power Button Circuit Board.

  15. Grasp, lift, and remove the LCD Module from the front panel. Grasp, lift, and remove the LCD Module from the front panel. Grasp, lift, and remove the LCD Module from the front panel.
    • Grasp, lift, and remove the LCD Module from the front panel.

  16. Unscrew the 2 screws holding the Power Button Circuit Board. Unscrew the 2 screws holding the Power Button Circuit Board.
    • Unscrew the 2 screws holding the Power Button Circuit Board.

  17. Lift and remove the Power Button Circuit Board.
    • Lift and remove the Power Button Circuit Board.

Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Hussam Alzamzami

Lid sinds: 25-09-14

216 Reputatie

1 Handleiding geschreven

Team

USF Tampa, Team 1-3, Brown Fall 2014 Lid van USF Tampa, Team 1-3, Brown Fall 2014

USFT-BROWN-F14S1G3

3 Leden

5 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 5

Afgelopen 30 dagen: 38

Altijd: 989