Ga door naar hoofdinhoud

Vind antwoorden in dit document

We hebben alle pagina’s op 7 al doorgenomen, zodat jij dat niet hoeft te doen. Stel je vraag en krijg meteen antwoord.

KOP SAF PRG 00002%20Hand%20and%20Portable%20Power%20Tools%20Program

7 pagina's · 177.58 KB · PDF

Hand and Portable Power Tools

This program outlines Kidd Operation's requirements for Employees and Contractors while using hand and portable power tools.

This program is to be used in conjunction with KOP-SAF-GDL-00005 - Guideline Hand Tools and KOP-SAF-GDL00004 - Guideline Portable Power Tools.

This program is not a training package. Training is required before using any hand and portable power tool.

2. Scope

This program covers all Kidd Operation Employees and Contractors who are designated by their departments to use hand and portable power tools.

This program references many types of hand and portable power tools including:

  • i. Hand Tools
  • ii. Portable Power Tools
  • Electric Tools,
  • Pneumatic Tools,
  • Liquid Fuel Tools,
  • Explosive-Actuated Tools, and
  • Hydraulic Tools.

This program does not include power tools that are fixed or mounted into place (such as lathes and bench grinders.)

3. Definitions

  • 3.1 Hand Tools: Hand tools have no power source other than the physical force applied by the user.
  • 3.2 Portable Power Tools: Portable power tools have a power source that could be: electric, pneumatic, liquid fuel, explosive-actuated or hydraulic.
  • 3.3 Personal Protective Equipment (PPE ): PPE is protective clothing, hats, goggles, or other equipment designed to protect the wearer's body from injury or illness caused by blunt impacts, electrical hazards, heat, vibration, chemicals, and infection .
  • 3.4 Restricted Tools: Restricted tools are only to be used in controlled conditions.
  • 3.5 Standardized Tools: Some tools are "preferred" to ensure safety and/or to ensure consistency with consumable purchasing.

4. Restricted Tools

  • 4.1 Gasoline or other volatile fuels shall not be used as power sources for tools in the underground environment.
  • 4.2 Sparking tools shall not be used around explosives or flammable material.
  • 4.3 Utility knives including box cutters, Exacto and Olfa L2 Knives: Utility knives are not to be carried or used except for spring-retractable safety cutters such as the SK4 or SK6.

Printed copies are not controlled.

VersionDocument NumberPage
6KOP-SAF-PRG-000021 of 7

Table Caption: This table displays version control information for a document, including its version number, document number, and page count.

Hand and Portable Power Tools

  • 4.4 Electric Grinders that do not meet the following four criteria are banned completely at Kidd Operations:
  • Double action switch - a button must be pressed to operate the on/off switch.
  • No lock button - the grinder must not be able to be locked in the on position, hands must be on the power switch at all times.
  • 180 o protecting guard - the grinder must be equipped with a guard covering at least 180 degrees.
  • Double handle - the grinder must be equipped with two handles. The front handle must be able to be fitted to the left- or to the right-hand side.

5. Standardized Tools

5.1 Grinders:

  • Dewalt 41/2' Grinder, Acklands Grainger Part Number D28402
  • Dewalt 4-1/2" / 5" Grinder, Acklands Grainger Part Number DW28114N
  • Dewalt 6" Grinder, Acklands Grainger Part Number DW28144N
  • Makita 4' Grinder, Acklands Grainger Part Number 9501B
  • Makita 4' Grinder, Acklands Grainger Part Number 9526NBH
  • Makita 4' Grinder, Acklands Grainger Part Number MKTGA4030
  • Makita 5" Grinder, Acklands Grainger Part Number MKT9005BY
  • Makita 7" Grinder, Acklands Grainger Part Number MKTGA7031Y
  • Makita 7' Grinder, Acklands Grainger Part Number MKTGA7020
  • Walter 41/2' Grinder, Acklands Grainger Part Number 6161G
  • Walter 4-1/2 Grinder, Acklands Grainger Part Number 6161J

6. Legislated Requirements

  • 6.1 All tools shall be maintained in a condition that does not endanger a worker.
  • 6.2 No tool shall be used:
  • while it is defective or hazardous or
  • when the weather or other conditions are such that its use is likely to endanger a worker; or
  • while it is being repaired or serviced, unless the repair or servicing requires that it be operated - at which time alternate controls are to be implemented.
  • 6.3 All tools shall be used in accordance with any operating manuals issued by the manufacturers.
  • 6.4 Every replacement part for a tool shall have at least the same safety factor as the part it is replacing.
  • 6.5 No modification to a part of a tool shall result in a reduction of the safety factor of the tool.
  • 6.6 No extension to a part of a tool shall result in a reduction of the safety factor of the tool.
  • 6.7 No repair to a part of a tool shall result in a reduction of the safety factor of the tool.
  • 6.8 No replacement of a part of a tool shall result in a reduction of the safety factor of the tool.
  • 6.9 Only trained and authorized personnel are permitted to repair and/or adjust hand and portable power tools.

7. Roles and Responsibilities

  • 7.1 Kidd Operations will provide its employees with initial and refresher training.
  • 7.2 Contractors are required to provide their employees with initial and refresher training before arriving on site. In certain circumstances, Kidd Operations may provide training for the contractor.

Printed copies are not controlled.

VersionDocument NumberPage
6KOP-SAF-PRG-000022 of 7

Table Caption: This table displays version, document number, and page information for a document, specifically showing version 6, document number KOP-SAF-PRG-00002, on page 2 of 7.

Hand and Portable Power Tools

  • 7.3 All Kidd Operation and contractor supervisors and employees are required to follow this program and its associated guidelines.
  • 7.4 Supervisor General Responsibilities
  • Ensure that employees attend training.
  • Ensure that hand and portable power tools are repaired when damaged or malfunctioning.
  • Ensure that modifications or additions which may affect the safe use of tools are not made without the manufacturer's prior written approval.
  • Ensure OEM tool safety and ergonomic feature developments are considered when purchasing new tools.

7.5 Employee General Responsibilities

  • Understand that the use of hand

Meld je gratis aan bij iFixit om het volledige document te lezen (7 pagina's)

We vragen je om een gratis account aan te maken, zodat we bots buiten de deur kunnen houden en iFixit voor mensen blijft.

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 3

Afgelopen 30 dagen: 22

Altijd: 173