sony_dsc-h300_ver1.0.pdf

SERVICE MANUAL

Ver. 1.0 2013.09

Internal memory ON BOARD Internal memory ON BOARD

DSC-H300

US Model Canadian Model AEP Model UK Model Russian Model E Model Chinese Model Brazilian Model

SERVICE NOTE (Check the following note before the service.)

1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-2. DEDICATED A/V CABLE (OPTIONAL ACCESSORY)

• 1-3. REGARDING FUSE

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DIGITAL STILL CAMERA

Revision History

Table Caption: This table outlines the version history of a document or project, detailing its official release date, revision history, contents, and any associated S.M. reviews. Version 1 was officially released in September 2013.

Camera

[System]

Image device: 7.76 mm (1/2.3 type) CCD,

Primary color filter

Total pixel: Approx. 20.4 Megapixels Effective pixel: Approx. 20.1 Megapixels Lens: 35× zoom lens

f = 4.5 mm - 157.5 mm (25 mm - 875 mm

(35 mm film equivalent))

F3.0 (W) - F5.9 (T)

While shooting movies (16:9):

30.3 mm - 1 060 mm

While shooting movies (4:3):

27.8 mm - 973 mm

SteadyShot: Optical

Burst shooting (when shooting with the largest pixel number):

Approx. 0.80 images/second (up to 100 im- ages)

File format:

Still images: JPEG (DCF, Exif, MPF Baseline) compliant, DPOF compatible Movies: MPEG-4 AVC/H.264

SPECIFICATIONS

Recording media: Internal Memory (Approx. 55 MB), 'Memory Stick Duo' media, 'Memory Stick Micro' media, SD cards, microSD memory cards

Flash: Flash range (ISO sensitivity (Recommended Exposure Index) set to Auto):

Approx. 0.4 m to 6.8 m (1.3 ft. to 22.3 ft.) (W)

Approx. 1.5 m to 3.6 m (4.9 ft. to 11.8 ft.) (T)

[Input and Output connectors]

USB / A/V OUT jack:

Video output

Audio output

USB communication

USB communication: Hi-Speed USB (USB 2.0)

[Screen]

LCD screen: 7.5 cm (3.0 type) TFT drive Total number of dots: 460 800 dots

Model information table

Table Caption: This table compares two Sony DSC-H300 models, highlighting differences in their target destinations and color systems, with neither model featuring GPS.

• Abbreviation

BR

: Brazilian model

CH

: Chinese model

CND : Canadian model

RU

: Russian model

[Power, general]

Power: LR6 (size AA) alkaline batteries (4), 6 V HR15/51: HR6 (size AA) Nickel-Metal Hy- dride batteries (4) (sold separately), 4.8 V

Power consumption (during shooting):

Approx. 1.6 W

Operating temperature: 0°C to 40°C

(32°F to 104°F)

Storage temperature: -20°C to +60°C (-4°F to +140°F)

Dimensions (CIPA compliant):

127.5 mm × 89.0 mm × 91.7 mm (5 1/8 inches

× 3 5/8 inches × 3 5/8 inches) (W/H/D)

Mass (CIPA compliant) (including four batteries and 'Memory Stick Duo' media): Approx. 590 g (1 lb 4.8 oz)

Microphone: Monaural

Speaker: Monaural

Exif Print: Compatible

PRINT Image Matching III: Compatible

Design and specifications are subject to change without notice.

Caution

Danger of explosion occurs if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.

注意

如果电池更换不当会有爆炸危险。 只能用同样类型或等效类型的电池来更换。 务必按照说明处置用完的电池。

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are 'pinched' or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 350°C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.

UNLEADED SOLDER

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

( Caution:

Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

• Set the soldering iron tip temperature to 350°C approximately. If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution:

The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges