2008 Dodge Avenger Frame And Bumpers
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
BUMPERS
SPECIFICATIONS
IORQUE SPECIFICATIONS BUMPERS
IORQUE SPECIFICATIONS
| DESCRIPTION | Ft. Lbs. | |
|---|---|---|
| Rear bumper reinforcement attaching nut | 28 | 21 |
| Front Crossmember to cradle bolts (3 | 50 | 41 |
| Front suspension crossmember frame rail torque boxes attaching bolts | 135 | 100 |
| Front suspension crossmember attaching_front and rear_ | 55 | |
| ForelAft crossmember anti roll through bolt | 50 | 37 |
| Radiator_support crossmember attaching bolts_ | 115 | 85 |
| Shear bracket fasteners | 55 | 41 |
Table Caption: This table lists torque specifications, in foot-pounds, for various automotive components, primarily related to front and rear bumper reinforcements, suspension crossmembers, and related brackets.
CLOSEOUT-LOWER FASCIA FRONT REMOVAL
- 1 . Remove fasteners (5) to lower closeout.
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
Fig 2: Identifying Closeout-Front Lower Fascia Courtesy of CHRYSLER LLC
- 2 Remove pins (1) to lower closeout. push
- 3 Remove the front lower fascia.
INSTALLATION
Fig 3: Identifying Lower Fascia Courtesy of CHRYSLER LLC
- Install closeout panel (1) onto fascia (3) push pins (2) and screws (4).
- 2 Install fasteners (5).
FASCIA-FRONT REMOVAL
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- Remove air inlet pin (4) and air-box fastener (2) push
- 2 Remove pins (2) and fascia fasteners (1) from grille. grille push
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 3_ Lift vehicle and on both the left and right remove two splash shield fasteners (1) and eight pins.
- 4 Remove splash shields from vehicle.
- 5 Remove closeout panel. See REMOVAL
- 6 Slide fascia forward disengaging from pins. push
- 7 . If equipped, disconnect lamp connectors. fog
- 8 Disconnect the side marker electrical connectors . lamp
- 9 Remove fascia from vehicle.
INSTALLATION
~
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 1 . Raise vehicle.
- 2 Raise fascia up to vehicle and connect connectors if equipped. fog lamp
- 3 Connect the side marker lamp electrical connectors.
- 4 Slide fascia into push pins ensuring proper seat.
- 5 Install closeout panel fasteners and pins. See INSIALLATION push
- 6 Install right and left splash shield fasteners and push pins.
- 7 Lower vehicle.
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 8 Place onto fascia. grille
- 9 Install pins (2) and fascia fasteners (1 ). Refer to INSIALLAIION grille push
- Install air box inlet pin (4) and fastener (2) push
FASCIA-REAR
REMOVAL
AVENGER
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- Open decklid.
- 2 Remove upper fascia push (1) pins
- 3 Raise vehicle.
- Remove lower fascia push pins (1)
- 5 Remove left and right splash shield pins and fasteners. push
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 6 Remove fascia fastener (2)
- 7 Slide fascia rearward from pins (1 ) push
- 8 Disconnect wire connector (1) and (2).
SEBRING SEDAN
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 1 . Release decklid latch and open decklid.
- 2 Remove three push-in fasteners (1) attaching center of fascia to rear closure panel.
- 3 Remove two wheelhouse fasteners and back splash shields exposing fascia to fender hidden fastener (1). pull
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 4 Remove lower fascia fasteners (2)
- 5 . Slide fascia rearward to disengage hooks holding fascia to bottom of quarter panel.
- 6 Remove fascia from vehicle.
AVENGER
- 1 . Raise vehicle.
- 2 Connect license plate wire connectors (1) and (2)
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- Slide rear fascia onto fascia locators (1).
- 4 Install fastener (2)
- 5 Install left and right splash shield push pins and fasteners.
- 6 Install lower fascia pins (1). push
- 7 . Lower vehicle.
- 8 Raise decklid.
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 9 Install upper fascia push pins.
SEBRING SEDAN
- Ensure that the energy management foam is properly installed in rear fascia.
- 2 Position fascia on vehicle.
- 3 Slide fascia forward to engage hooks attaching fascia to bottom of quarter panel.
- 4 Install push-in fasteners (1) attaching center of fascia to trunk opening.
- 5 Install screws (2) attaching fascia to quarter panel at wheelhouse opening.
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 6 Install lower fascia fasteners .
- 7 . Install fasteners attaching rear splash shields to wheelhouse.
REINFORCEMENT-BUMPER FRONT
REMOVAL
- Remove front fascia. See REMQVAL:
- 2 Remove hood latch fasteners 1) and move hood latch out of way.
- 3 Remove left and right brace fasteners (2) and braces .
- 4 Remove left and right horn fasteners and horn. Refer to REMOVAL
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
- 5 Remove ambient temperature sensor from bumper reinforcement. Refer to REMOVAL
- 6 Remove coolant lines pins from bumper reinforcement. push
- 7 . Remove bumper reinforcement fasteners and bumper from vehicle.
INSTALLATION
com
2008 Dodge Avenger SE
2008 ACCESSORIES & EQUIPMENT Frame & Bumpers Avenger & Sebring
D >
- 1 . Place bumper reinforcement up to vehicle and install fasteners. Tighten to 27 N.m (239 inch Ibs.)-
- 2 Install coolant line pins to bumper. push
- 3 Install ambient temperature sensor. Refer to
Meld je gratis aan bij iFixit om het volledige document te lezen (49 pagina's)
We vragen je om een gratis account aan te maken, zodat we bots kunnen blokkeren en iFixit voor mensen kunnen houden.
