Security And Locks

Security and Locks

Key Coding Construction

Key Usage and Identification

Key is used for ignition and door lock cylinder. Keys are cut on both edges to make them reversible.

Key identification is obtained from five character key code stamped on key code tag. Using this key code, key code cutting combination can be determined from a code list (available to owners of key cutting equipment from suppliers).

If key codes are not available from records or tags, key code can be obtained from the right hand door lock cylinder (if lock has not been replaced). Lock cylinders supplied by the factory as service parts are unmarked.

If original key is available, key code cutting combination can be determined by laying key.

Rear End Door Opener System Description

General Description

S4RS0A9601001

S4RS0A9601002

Rear end door opener system consists of rear end door opener switch (1), rear end door opener relay (in BCM), rear end door lock assembly (2) and BCM (3) (in junction block assembly).

Rear end door opener system is activated by pushing rear end door opener switch after all doors are unlocked by manual door switch, key cylinder switch or keyless entry transmitter.

When rear end door opener switch pushed rear end door opener relay is ON. Then, BCM releases latch of rear end door lock assembly from striker and rear end door can be opened.

In addition, in case that rear end door cannot be opened by rear end door opener switch, rear end door can be opened by emergency lever (4) in rear end door lock assembly.

I4RS0A960025-

Component Location

Power Door Lock and Keyless Entry System Component Location

S4RS0A9603001

I4RS0A960001-

Table Caption: This table lists eight components related to a vehicle's keyless entry and power door lock system. The components include the receiver, transmitter, switches, actuators for both front and rear doors, and the Body Control Module (BCM).

Diagnostic Information and Procedures

Power Door Lock System Symptom Diagnosis

NOTE:

• Use SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or output side of BCM. For checking procedure, refer to 'Diagnosis Using Output Test Function of SUZUKI Scan Tool' under 'Scan Tool Data: in Section 10B'.
• Check each part in the order from the top of the following list.

Table Caption: This table outlines troubleshooting steps for power door lock system malfunctions, listing possible causes and corresponding corrections or reference items for each condition. It systematically addresses issues affecting all doors, specific switches, and individual door actuators.

Power Door Lock System Operation Inspection

• 1. Check the following operation:
• a) Turn the driver side key cylinder to LOCK position with door key once, check all doors lock.
• b) Turn the driver side door key cylinder to UNLOCK position with door key twice, check all doors unlock. If malfunction is found, go to 'Power Door Lock System Symptom Diagnosis: '.

S4RS0A9604001

S4RS0A9604002

Keyless Entry System Symptom Diagnosis

NOTE:

• Confirm that power door lock system is in good condition before referring to the following possible causes.
• Check each part in the order from the top of the following list.

Table Caption: This table outlines troubleshooting steps for common problems with a keyless entry system, listing possible causes, and corresponding corrections or reference items for diagnosis and repair. It covers issues with locking/unlocking, turn signal function, interior light activation, and transmitter code programming.

Keyless Entry System Operation Inspection

S4RS0A9604005

• 1. Confirm that power door lock system operates normally, refer to 'Power Door Lock System Operation Inspection: '.
• 2. All doors are closed and unlocked.
• 3. Check the following operation:
• a) Push 'lock' button (1) on transmitter (2) once, and check all doors lock and hazard waning lights flash once.
• b) Push 'unlock' button (3) on transmitter (2) twice, and check all doors unlock and hazard waning lights flash twice and interior light turns on several seconds with the interior light switch in the middle position.

S4RS0A9604004

I3RH0A960005-

If malfunction is found, go to 'Keyless Entry System Symptom Diagnosis: '.

Rear End Door Opener System Symptom Diagnosis

NOTE:

• Use SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or output side of BCM. For checking procedure, refer to 'Diagnosis Using Output