Ga door naar hoofdinhoud

Vind antwoorden in dit document

We hebben alle pagina’s op 70 al doorgenomen, zodat jij dat niet hoeft te doen. Stel je vraag en krijg meteen antwoord.

DSC-W230 SM

70 pagina's · 5.50 MB · PDF

SERVICE MANUAL

Internal memory ON BOARD Internal memory ON BOARD

Photo: Silver

Link Link
SPECIFICATIONSBLOCK DIAGRAMSPRINTED WIRING BOARDS
SERVICE NOTEFRAME SCHEMATIC DIAGRAMREPAIR PARTS LIST
DISASSEMBLYSCHEMATIC DIAGRAMS

Table Caption: This table categorizes technical documentation related to a product, listing specifications, diagrams, service information, and parts lists under different headings. It appears to organize essential information for understanding, maintaining, and repairing the product.

¥ Precaution on Replacing the SY-230 Board

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DSC-W230

LEVEL 2

US Model Canadian Model AEP Model UK Model E Model Australian Model Korea Model Argentine Model

DIGITAL STILL CAMERA

2009G0800-1 ' 2009.07 Published by Tokai TEC

Camera

[System]

Image device:

7.79 mm (1/2.3 type) color CCD, Primary color filter

Total pixel number of camera:

Approx. 12.4 Megapixels

Effective pixel number of camera:

Approx. 12.1 Megapixels

Lens: Carl Zeiss Vario-Tessar 4

×

zoom lens

f = 5.35 - 21.4 mm (30 - 120 mm (35 mm

film equivalent)) F2.8 (W) - F5.8 (T)

Exposure control:

Automatic exposure, Scene Selection

(11 modes)

White balance: Automatic, Daylight, Cloudy,

Fluorescent 1,2,3, Incandescent, Flash

Underwater White Balance: Auto, Underwater

1,2, Flash

File format (DCF compliant):

Still images: Exif Ver. 2.21 JPEG compliant,

DPOF compatible

Movies: MPEG1 compliant (Monaural)

Recording media: Internal Memory (approx.

15 MB), 'Memory Stick Duo' media

Flash: Flash range (ISO sensitivity

(Recommended exposure Index) set to Auto):

Approx. 0.2 to 3.9 m (7 7/8 inches to 12 feet

9 5/8 inches) (W)/approx. 0.5 to 1.9 m (1 feet

7 3/4 inches to 6 feet 2 7/8 inches) (T)

[Input and Output connectors]

Multi use terminal Type2b (AV-out(SD/HD

Component)/USB/DC-in):

Video output

Audio output (Monaural)

USB communication

USB communication: Hi-Speed USB (USB 2.0 compliant)

SPECIFICATIONS

[LCD screen]

LCD panel: 7.5 cm (3.0 type) TFT drive Total number of dots: 230 400 (960 × 240) dots

[Power, general]

Power: Rechargeable battery pack

NP-BG1, 3.6 V

NP-FG1 (sold separately), 3.6 V

AC-LS5K AC Adaptor (sold separately),

4.2 V

Power consumption (during shooting):

1.1 W

Operating temperature: 0ßC to 40ßC (32ßF to

104ßF)

Storage temperature: -20ßC to +60ßC (-4ßF to

+140ßF)

Dimensions:

95.2

×

56.5

×

21.8 mm (3 3/4

×

2 1/4

×

7/8 inches) (W/H/D, excluding

protrusions)

Mass:

Approx. 156 g (5.5 oz) (including NP-BG1 battery pack, 'Memory Stick Duo' media)

Microphone: Monaural

Speaker: Monaural

Exif Print: Compatible

PRINT Image Matching III: Compatible

PictBridge: Compatible

BC-CSGD/BC-CSGE battery

charger

Power requirements: AC 100 V to 240 V, 50/60 Hz, 2 W Output voltage: DC 4.2 V, 0.25 A Operating temperature: 0ßC to 40ßC (32ßF to 104ßF) Storage temperature: -20ßC to +60ßC (-4ßF to +140ßF) Dimensions: Approx. 83 × 55 × 24 mm (3 3/8 × 2 1/4 × 31/32 inches) (W/H/D) Mass: Approx. 55 g (1.9 oz)

Rechargeable battery pack NP-BG1

Used battery: Lithium-ion battery

Maximum voltage: DC 4.2 V

Nominal voltage: DC 3.6 V

Maximum charge current: 1.44 A

Maximum charge voltage: DC 4.2 V

Capacity:

typical: 3.4 Wh (960 mAh)

minimum: 3.3 Wh (910 mAh)

Design and specifications are subject to change without notice.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT ¸ LA SÉCURITÉ!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIØCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIØSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

  1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.
  2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.
  3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
  4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
  5. Check the B+ voltage to see it is at the values specified.
  6. Flexible Circuit Board Repairing
  7. ¥ Keep the temperature of the soldering iron around 270ßC during repairing.
  8. ¥ Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
  9. ¥ Be careful not to apply force on the conductor when soldering or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

  • ¥ Unleaded solder melts at a temperature about 40 ° C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

  • Soldering irons using a temperature regulator should be set to about 350 ° C.

Caution: The

Meld je gratis aan bij iFixit om het volledige document te lezen (70 pagina's)

We vragen je om een gratis account aan te maken, zodat we bots buiten de deur kunnen houden en iFixit voor mensen blijft.

Weergavestatistieken:

Afgelopen 24 uren: 3

Afgelopen 7 dagen: 9

Afgelopen 30 dagen: 33

Altijd: 1,493