Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Onderdelen & Gereedschap

2.3GHz, 2.6GHz, or 2.7GHz quad-core Intel Core i7 processor (Turbo Boost up to 3.7GHz) with 6MB shared L3 cache.

519 Vragen Bekijk alle

MacBook doesn't turn on, no light on magsafe 2 charger

Hello everyone,

Last year the charger of my macbook got faulty and stopped working, also the macbook turned off.

Lately I aquired myself a new original magsafe charger 2(85 watt) but sadly this did not help. The macbook won’t turn on and the indication light on the charger stays off.

The battery wasn’t its best anymore, I did have a battery service message and sometimes the macbook would go off around 35%.

What could be the cause of the not turning on/charging? and is it fixable ?

Thanks in advance


Beantwoord! View the answer Dit probleem heb ik ook

Is dit een goede vraag?

Score 0
Voeg een opmerking toe

Essentiële Electronica Toolkit

Kleine toolkit. Grote dromen.

Shop Toolkits


Shop Toolkits

2 Antwoorden

Gekozen oplossing

If the MagSafe cord LED is not lighting that’s a sign the systems MagSafe connector needs cleaning or replacing. Review this Apple T/N Apple Portables: Troubleshooting MagSafe adapters Jump down to point #7

Here’s the needed MagSafe connector for you system MacBook Pro 15" Retina (Mid 2012-Early 2013) MagSafe 2 DC-In Board. You could also have a bad I/O cable as the power goes to the I/O board and then through the I/O cable to the main logic board MacBook Pro 15" Retina (Mid 2012-Early 2013) I/O Board Cable

If you disconnect your battery your MagSafe charger should be able to run your system.

MacBook Pro 15" Retina (Mid 2012-Early 2013) I/O Board Cable Afbeelding


MacBook Pro 15" Retina (Mid 2012-Early 2013) I/O Board Cable


MacBook Pro 15" Retina (Mid 2012-Early 2013) MagSafe 2 DC-In Board Afbeelding


MacBook Pro 15" Retina (Mid 2012-Early 2013) MagSafe 2 DC-In Board


Was dit antwoord nuttig?

Score 3


Thanks for the suggestion I wil take a closer look to the connector. I will recieve a pentalobe screwdriver so I can inspect the inside of the macbook and decide if i need a new DC/IO cable. I will report back if i got any results!


I ordered the parts and tools. This week I'm going to replace the mentioned parts. I will update with results.


I replaced the parts, and the magsafe does have a signal now. It's orange seeming its trying to charge. But when I press the power button I don't get any response yet. Is it possible dat its needs more time cause the macbook being drained for a long time?


Disconnect the battery and the MagSafe, then press and hold the power button a good minute. Now plug in the MagSafe only! The system should spontaneously start. If it doesn't then your logic board has issues! Did you have a liquid spill at one point?


I will try this as soon as I can. Do I connect the magsafe while i'm holding the button? I checked the board and the waterindicators, no sign of any water damage.


2 commentaren meer tonen

Voeg een opmerking toe

Extremely worn battery? Miscalibration?

Was dit antwoord nuttig?

Score 0


Does that make the charger not do anything? I did look up some articles but almost all of them talked about a macbook that could be turned on or a charger that functioned. Mine doesn't have both of the options.


Maybe try a different charger? Or try charging a different macbook with yours.


Voeg een opmerking toe

Voeg je antwoord toe

Jeroen zal eeuwig dankbaar zijn.

Afgelopen 24 uren: 33

Afgelopen 7 dagen: 189

Afgelopen 30 dagen: 921

Altijd: 5,084