Repareer je spullen Gemeenschap Winkel
Help

Deze versie is geschreven door: Zack Sg

Titel:

Can MG 8331S be soldered on?

Tekst:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
Edit1: General area.
[image|2747051]
Edit2: Battery Clip Connector Component (board side - female)
[image|2747060]
Location on board:
[image|2747058]
[image|2747061]
Edit3:
[image|2747065]
-[image|2747066] (Flipped over the connector)
+[image|2747066]
+
+(Flipped over the connector)

Toestel:

Soldering

Status:

open

Goedgekeurd antwoord:

+750010

Bewerkt door: Zack Sg

Titel:

Can MG 8331S be soldered on?

Tekst:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
Edit1: General area.
[image|2747051]
Edit2: Battery Clip Connector Component (board side - female)
[image|2747060]
Location on board:
-[image|2747058] (Source: https://www.ifixit.com/Guide/Samsung+Galaxy+Note20+Ultra+Motherboard+Replacement/142701)
+[image|2747058]
[image|2747061]
+
+Edit3:
+
+[image|2747065]
+
+[image|2747066] (Flipped over the connector)

Toestel:

Soldering

Status:

open

Bewerkt door: Zack Sg

Titel:

Can MG 8331S be soldered on?

Tekst:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
-Edit1: General area. [image|2747051]
+Edit1: General area.
+
+[image|2747051]
+
+Edit2: Battery Clip Connector Component (board side - female)
+
+[image|2747060]
+
+Location on board:
+
+[image|2747058] (Source: https://www.ifixit.com/Guide/Samsung+Galaxy+Note20+Ultra+Motherboard+Replacement/142701)
+
+[image|2747061]

Toestel:

Soldering

Status:

open

Bewerkt door: Zack Sg

Titel:

Can MG 8331S be soldered on?

Tekst:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
+
+Edit1: General area. [image|2747051]

Toestel:

Soldering

Status:

open

Origineel bericht door: Zack Sg

Titel:

Can MG 8331S be soldered on?

Tekst:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.

[image|2746283]

However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.

Thank you in advance.

Toestel:

Soldering

Status:

open