Deze versie is geschreven door: Nick
Tekst:
| - | The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' |
|---|---|
| + | The problem with these printers is OEM Epson ink is so think, it adds fuel to the problem. Epson pigmented inks (DuraBrite/Ultra) tend to accelerate the problem! The ink being thinner on dye base models helps a lot since it is less prone to clog issues (Claria/Claria HD)'''''.''''' |
| + | |
| + | '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| - | ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but |
| + | ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but will come back to sanity. Getting close enough is fine.''''' |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| If you must, the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20-30% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. | |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or trigger the ink swap mode. | |
| *** '''CAUTION: YOU HAVE A WETNESS SENSOR PRINTER, PREMATURE REMOVAL IS KNOWN TO KILL THE CARTS.''' | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the head. If you do not do this the printhead might get damaged due to degraded rubber parts ruined by sitting alcohol.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| If you must, the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20-30% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. | |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or trigger the ink swap mode. | |
| - | *** '''CAUTION: YOU HAVE A WETNESS SENSOR PRINTER |
| + | *** '''CAUTION: YOU HAVE A WETNESS SENSOR PRINTER, PREMATURE REMOVAL IS KNOWN TO KILL THE CARTS.''' |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the head. If you do not do this the printhead might get damaged due to degraded rubber parts ruined by sitting alcohol.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| - | If you must |
| + | If you must, the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20-30% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or trigger the ink swap mode. | |
| + | *** '''CAUTION: YOU HAVE A WETNESS SENSOR PRINTER. PREMATURE REMOVAL IS KNOWN TO KILL THE CARTS.''' |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| - | * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the |
| + | * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the head. If you do not do this the printhead might get damaged due to degraded rubber parts ruined by sitting alcohol.''''' |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20-30% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. | |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| - | ** If the tab isn’t visible, look around for it, find a service manual or |
| + | ** If the tab isn’t visible, look around for it, find a service manual or trigger the ink swap mode. |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| - | * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged |
| + | * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged due to degraded rubber parts ruined by sitting alcohol..''''' |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| - | If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. |
| + | If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20-30% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or use ink change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and fail.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initiate a ink change (wastes ink) | |
| ** Try and avoid if possible | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| - | If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need |
| + | If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water (1:3 is safer, but is less effective). This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need high concentration alcohol since you lose ~20% of it’s strength. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or use ink change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and fail.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' | |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| - | * Initialate a ink change (wastes ink) |
| + | * Initiate a ink change (wastes ink) |
| + | ** Try and avoid if possible |
| * Find the release latch that holds the printhead in and move the head. | |
| - | ** '''''Move it back once you’re done and power cycle the printer - it throws it off |
| + | ** '''''Move it back once you’re done and power cycle the printer - it throws it off at startup, but it will come back to sanity. Getting close enough is fine.''''' |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need 99% for this as the dilution process will reduce it’s strength by ~20%. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. | |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or use ink change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and fail.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining |
|---|---|
| + | The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining printer damage. Unless you know how, DO NOT remove the printhead unless you have to!''''' |
| While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: | |
| * Initialate a ink change (wastes ink) | |
| * Find the release latch that holds the printhead in and move the head. | |
| ** '''''Move it back once you’re done and power cycle the printer - it throws it off if you don’t for a little bit, but it will come back to sanity.''''' | |
| When it comes to cleaner you have two choices: | |
| * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) | |
| ** Follow the provided instructions with the kit | |
| DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. | |
| If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need 99% for this as the dilution process will reduce it’s strength by ~20%. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. | |
| Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. | |
| ** If the tab isn’t visible, look around for it, find a service manual or use ink change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. | |
| * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. | |
| * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and fail.''''' | |
| ** '''''Follow the kit instructions for premade solution.''''' | |
| * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. | |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. | |
| If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these printers is Epson ink is |
|---|---|
| + | The problem with these printers is Epson ink is the OEM ink is so think, it adds fuel to the problem. However, the added exposure problem is more prevalent on the DuraBrite Ultra hardware (pigment base) and the dye ink (Claria/Claria HD) tends to be more reasonable. '''''To make matters worse, the head is difficult to remove without sustaining breaking the printers. Unless you know how, DO NOT remove the printhead unless you have to!''''' |
| - | While it’s more or less impossible to remove the head, the problem can be solved |
| + | While it’s more or less impossible to remove the head, the problem can be solved with printhead cleaner, vinyl tubing and a syringe. This does get messy, so wear gloves if ink stains on skin bother you. There’s 2 ways to free it for cleaning: |
| + | * Initialate a ink change (wastes ink) |
| + | * Find the release latch that holds the printhead in and move the head. |
| + | ** '''''Move it back once you’re done and power cycle the printer - it throws it off if you don’t for a little bit, but it will come back to sanity.''''' |
| When it comes to cleaner you have two choices: | |
| - | * Premade cleaner ( |
| + | * Premade cleaner (Search '''''Epson printhead cleaner''''' on [https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313.TR1.TRC0.A0.H0.XEpson+printhead+cleaner.TRS0&_nkw=Epson+printhead+cleaner&_sacat=0|eBay]) |
| ** Follow the provided instructions with the kit | |
| - | * Homemade cleaner |
| - | ** Use common sense and don’t inject too much at once. The most I’d try is 4-5mL at a time. If it doesn’t work within 4-5 attempts, it’s too far gone or needs a premade cleaner. |
| - | If you care about the printer, you're probably better off getting premade cleaner. If you don't care if you damage the printer, the homemade option may work. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. |
| + | DO NOT use homebrew cleaners unless you know how to make it in a way that doesn’t ruin the anti clog coating or puts the head at risk of permanent failure resulting in a fatal error - even if you don’t mind the risk. |
| - | |
| + | If you must. the formula I'd recommend for this is 1 part alcohol (91-99%) to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. You will need 99% for this as the dilution process will reduce it’s strength by ~20%. Hot water alone doesn't work on Epson printers because of the water resistance of their inks. |
| - | |
| + | Either way, these are the general instructions most premade kits use in terms of getting the head in a cleaning state - beyond this, follow the kit instructions: |
| - | * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. |
| - | * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode; it will do the same job. |
| + | * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. You don’t want this to happen. |
| + | * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. |
| + | ** If the tab isn’t visible, look around for it, find a service manual or use ink change mode. |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| - | * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matched packs. |
| - | * Slowly inject solution into the printer. It may help to spread the injections as you go. |
| - | * After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and leak ink due to failed seals. |
| - | * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. |
| + | * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matches. |
| + | * Slowly inject solution into the printhead. Work all of the nozzles and then clean the stubborn ones again. |
| + | * '''''Homebrew only: After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and fail.''''' |
| + | ** '''''Follow the kit instructions for premade solution.''''' |
| + | * Use a microfiber cloth to dry the printhead nozzles if needed. The ink cartridges should not be inserted when solution is present. |
| * Verify the results with a nozzle check. | |
| ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). | |
| - | While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. If you can do it, the procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
| + | While your Epson is one of the few models where the printhead is actually designed to be removed a lot more easily, I would still advise against it UNLESS injections do not help. This process is difficult and also easy for a beginner DIYer to get wrong and cause $$$ damage that totals out the printer due to user error. |
| + | |
| + | If you can do it, the procedure typically involves removing the ink chip reader plate, 2-4 screws and disconnecting two flat flex cables. After removing the head, soak it solution - ideally just enough to not get cleaner into the electronics. If it does happen, further disassembly and an air compressor is required. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment |
|---|---|
| + | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment printers (Ex: DuraBrite) since it’s thicker then the dye ink Epson uses in printers that use the Claria/Claria HD ink. To make matters worse, the head is difficult to remove without sustaining permanent damage to the printer. I don’t recommend even TRYING to remove the printhead. |
| - | Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. While liquid injection isn't as good, it isn't as deadly to the printhead. When it comes to cleaner you have two choices: |
| + | While it’s more or less impossible to remove the head, the problem can be solved by injecting printhead cleaner. This does get messy, so wear gloves if ink stains on skin bother you. It’s usually pretty easy to unlock the head on most models (look for the white tab), but your mileage may vary. This may take a few more tries, but it doesn’t destroy printheads and entire printers in the process. |
| + | |
| + | When it comes to cleaner you have two choices: |
| * Premade cleaner (check sites like eBay for Epson printhead cleaner) | |
| + | ** Follow the provided instructions with the kit |
| * Homemade cleaner | |
| + | ** Use common sense and don’t inject too much at once. The most I’d try is 4-5mL at a time. If it doesn’t work within 4-5 attempts, it’s too far gone or needs a premade cleaner. |
| + | If you care about the printer, you're probably better off getting premade cleaner. If you don't care if you damage the printer, the homemade option may work. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. |
| - | If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. |
| - | |
| - | If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. |
| - | |
| - | Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. |
| + | Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol (91%). Hot water alone doesn't work on Epson printers. |
| If you decide to go the homemade cleaner route, this is the procedure I recommend: | |
| - | * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and |
| - | * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. |
| + | * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and trigger early waste ink pad failure. |
| + | * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode; it will do the same job. |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| - | * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. |
| - | * Slowly inject solution into the printer. |
| - | * After cleaning the printhead, inject distilled water |
| + | * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. Measure it or buy a few possible matched packs. |
| + | * Slowly inject solution into the printer. It may help to spread the injections as you go. |
| + | * After cleaning the printhead, inject distilled water to purge the alcohol mix. If you do not do this the printhead might get damaged and leak ink due to failed seals. |
| * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. | |
| - | * Verify the results with a nozzle check. |
| - | |
| - | While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. |
| + | * Verify the results with a nozzle check. |
| + | ** To prevent it from happening again, the best way is a weekly nozzle check (every 3 days in humid climates). |
| + | While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. If you can do it, the procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment |
|---|---|
| + | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment ink printers (Ex: DuraBrite) then it is on dye ink printers (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to remove without damaging the actual printer on a lot of them. However, the problem can be solved by injecting cleaner into the head. Cleaning these printers is a messy procedure, so wear gloves if you don't like getting ink stains on your skin. |
| Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. While liquid injection isn't as good, it isn't as deadly to the printhead. When it comes to cleaner you have two choices: | |
| * Premade cleaner (check sites like eBay for Epson printhead cleaner) | |
| * Homemade cleaner | |
| If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. | |
| If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. | |
| Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. | |
| If you decide to go the homemade cleaner route, this is the procedure I recommend: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and cause the printers to trigger the waste ink warning earlier then it should. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. | |
| * Slowly inject solution into the printer. Do this no more then 5 times total, but no more then 1-2 injections at one given time. | |
| * After cleaning the printhead, inject distilled water through the printhead to purge the alcohol mix. If you do not do this the printhead might get damaged and your prints will look like crap. | |
| * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. | |
| * Verify the results with a nozzle check. Do this once a week to prevent future clogging (do this more often in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. The procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment based Epson printers (Ex: DuraBrite) then it is on dye based models (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to |
|---|---|
| + | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment based Epson printers (Ex: DuraBrite) then it is on dye based models (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to remove without damaging the actual printer on a lot of them. However, the problem can be solved by injecting cleaner into the head. Cleaning these printers is a messy procedure, so wear gloves if you don't like getting ink stains on your skin. |
| Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. While liquid injection isn't as good, it isn't as deadly to the printhead. When it comes to cleaner you have two choices: | |
| * Premade cleaner (check sites like eBay for Epson printhead cleaner) | |
| * Homemade cleaner | |
| If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. | |
| If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. | |
| Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. | |
| If you decide to go the homemade cleaner route, this is the procedure I recommend: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and cause the printers to trigger the waste ink warning earlier then it should. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. | |
| * Slowly inject solution into the printer. Do this no more then 5 times total, but no more then 1-2 injections at one given time. | |
| * After cleaning the printhead, inject distilled water through the printhead to purge the alcohol mix. If you do not do this the printhead might get damaged and your prints will look like crap. | |
| * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. | |
| * Verify the results with a nozzle check. Do this once a week to prevent future clogging (do this more often in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. The procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment based Epson printers (Ex: DuraBrite) then it is on dye based models (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to replace without damaging the actual printer on a lot of them. However, the problem can be solved by injecting cleaner into the head. Cleaning these printers is a messy procedure, so wear gloves if you don't like getting ink stains on your skin. | |
| - | Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. |
| + | Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. While liquid injection isn't as good, it isn't as deadly to the printhead. When it comes to cleaner you have two choices: |
| * Premade cleaner (check sites like eBay for Epson printhead cleaner) | |
| * Homemade cleaner | |
| If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. | |
| If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. | |
| Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. | |
| If you decide to go the homemade cleaner route, this is the procedure I recommend: | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and cause the printers to trigger the waste ink warning earlier then it should. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. | |
| * Slowly inject solution into the printer. Do this no more then 5 times total, but no more then 1-2 injections at one given time. | |
| * After cleaning the printhead, inject distilled water through the printhead to purge the alcohol mix. If you do not do this the printhead might get damaged and your prints will look like crap. | |
| * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. | |
| * Verify the results with a nozzle check. Do this once a week to prevent future clogging (do this more often in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. The procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment based Epson printers (Ex: DuraBrite) then it is on dye based models (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to replace without damaging the actual printer on a lot of them. However, the problem can be solved by injecting cleaner into the head. Cleaning these printers is a messy procedure, so wear gloves if you don't like getting ink stains on your skin. | |
| - | Since these printers have heads that are just about impossible to remove without damage, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. Injecting liquid ensures you won't trash the printer in the process. When it comes to cleaner you have two choices: |
| + | Since most Epson printheads are nearly impossible to remove, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. Injecting liquid ensures you won't trash the printer in the process. When it comes to cleaner you have two choices: |
| + | |
| * Premade cleaner (check sites like eBay for Epson printhead cleaner) | |
| * Homemade cleaner | |
| If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. | |
| If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. | |
| + | |
| Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. | |
| If you decide to go the homemade cleaner route, this is the procedure I recommend: | |
| + | |
| * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and cause the printers to trigger the waste ink warning earlier then it should. | |
| * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. | |
| * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. | |
| * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. | |
| * Slowly inject solution into the printer. Do this no more then 5 times total, but no more then 1-2 injections at one given time. | |
| * After cleaning the printhead, inject distilled water through the printhead to purge the alcohol mix. If you do not do this the printhead might get damaged and your prints will look like crap. | |
| * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. | |
| * Verify the results with a nozzle check. Do this once a week to prevent future clogging (do this more often in humid climates). | |
| While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. The procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these is the head |
|---|---|
| + | The problem with these printers is Epson ink is so thick if you use OEM ink. However, this problem is more prevalent on pigment based Epson printers (Ex: DuraBrite) then it is on dye based models (Ex: Claria series). To make matters worse, the head is VERY DIFFICULT to replace without damaging the actual printer on a lot of them. However, the problem can be solved by injecting cleaner into the head. Cleaning these printers is a messy procedure, so wear gloves if you don't like getting ink stains on your skin. |
| - | If you go with hot water and alcohol, here's how you do it: |
| + | Since these printers have heads that are just about impossible to remove without damage, it's better to unlock the printhead and inject solution to fix the problem. However, if you can remove it without damage you can do a much better job cleaning the printhead. Injecting liquid ensures you won't trash the printer in the process. When it comes to cleaner you have two choices: |
| + | * Premade cleaner (check sites like eBay for Epson printhead cleaner) |
| + | * Homemade cleaner |
| - | * Loosen the printhead. On some models, there will be a white tab you can push to free the head up. On others you will need to put it into ink change mode, remove the cartridges and unplug the printer. The easiest way to tell is to see if the printhead comes to the center when you open the lid. |
| - | * Fold some napkins up and put them in the printer's track. You will need to make sure you do not put too many in or the head will not go there easily. The average is 3-5. |
| - | * Remove the ink cartridges from the printhead. Set these aside somewhere safe. |
| - | * Get a plastic tube and syringe that can accept this tube. Get your 70% alcohol and push it through the printhead '''slowly''' to get the dried ink out. Do this 2-3 times. |
| - | * Once you do this, push distilled water through the printhead and do this 5-6 times to make sure the alcohol is out of the printhead. |
| - | * Dry the printhead spikes with a lint-free cloth.Once you do this, run a nozzle check and see if it's clear. If not, repeat this until all of the ink comes out of the printhead. Run a nozzle check once a week to keep the ink from drying out if you do not use the printer on a regular basis. |
| + | If you buy cleaner on eBay (or a similar site), simply follow the instructions on the bottle for the portions you are supposed to put in the printhead to clear the clog. If you go the homemade cleaner route, you kind of need to figure out how many injections are needed to unclog the printer. I'd recommend no more then 2 4mL injections at one given time. You need to get enough in there to break the clog down, BUT also not use too much. |
| - | You have one of the few Epson printers that can have the head removed without damage, but I still do not recommend this unless you are willing to risk destroying your printer. To remove the head you typically remove 2-4 screws and disconnect flat flex cables. You will then soak the printhead rather then use syringes and plastic tubing. |
| + | If you care about the printer, you're better off getting premade cleaner. If you don't care if you damage the printer, the homemade option is worth trying. The formula I'd recommend for this is 1 part alcohol to 2 parts water. This should dilute the alcohol to a safe level while retaining the ability to clear the clog. |
| + | Since you are diluting the alcohol 1:2, you need strong alcohol. Because of this, I would recommend using high concentration isopropyl alcohol. For a percentage, I'd recommend at least 90%. Hot water alone doesn't work very well in Epson printers. |
| + | |
| + | If you decide to go the homemade cleaner route, this is the procedure I recommend: |
| + | * Put 4-5 napkins in the print track. If you do not do this, the ink will go into your waste ink pads and cause the printers to trigger the waste ink warning earlier then it should. |
| + | * Loosen the printhead. On printers with a white tab next to the service station, release the tab in the unlocked position. If your printer does not have this, put the printer in the cartridge change mode. |
| + | * Put the ink cartridges aside. You do not need to put them in a bag, but it is recommended if you can do so. |
| + | * Find some plastic tubing that fits over the Epson nozzles. You want tubing that fits snugly, but also isn't loose. |
| + | * Slowly inject solution into the printer. Do this no more then 5 times total, but no more then 1-2 injections at one given time. |
| + | * After cleaning the printhead, inject distilled water through the printhead to purge the alcohol mix. If you do not do this the printhead might get damaged and your prints will look like crap. |
| + | * Use a lint free cloth to dry the printhead nozzles. The ink cartridges should not be inserted when water is on the tips where the ink cartridges sit. |
| + | * Verify the results with a nozzle check. Do this once a week to prevent future clogging (do this more often in humid climates). |
| + | |
| + | While your Epson is one of the few models where the printhead is actually designed to be removed, I would still advise against it UNLESS injections do not help. This process is difficult and easy for a beginner to get wrong and destroy the printer. The procedure typically involves removing 2-4 screws and disconnecting two flat flex cables. Once the head is removed, soak it in the solution. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these is the head design and the thickness of Epson ink. This is more of a problem on the DuraBrite pigment models but the dye based (Claria, etc.) can clog like this just as easily. The best way to fix it is a hot water or 70% alcohol and hot water injection, or removing the printhead and soaking it if you can remove it without damage. Most Epson printers get damaged by mere attempts. You should also be aware of the mess this procedure makes, so wear gloves if you do not want to get ink stains on your skin. |
|---|---|
| + | The problem with these is the head design and the thickness of Epson ink. This is more of a problem on the DuraBrite pigment models but the dye printers (Claria, etc.) can clog like this just as easily. The best way to fix it is a hot water or 70% alcohol and hot water injection, or removing the printhead and soaking it if you can remove it without damage. Most Epson printers get damaged by mere attempts. You should also be aware of the mess this procedure makes, so wear gloves if you do not want to get ink stains on your skin. |
| + | |
| If you go with hot water and alcohol, here's how you do it: | |
| + | |
| * Loosen the printhead. On some models, there will be a white tab you can push to free the head up. On others you will need to put it into ink change mode, remove the cartridges and unplug the printer. The easiest way to tell is to see if the printhead comes to the center when you open the lid. | |
| * Fold some napkins up and put them in the printer's track. You will need to make sure you do not put too many in or the head will not go there easily. The average is 3-5. | |
| * Remove the ink cartridges from the printhead. Set these aside somewhere safe. | |
| * Get a plastic tube and syringe that can accept this tube. Get your 70% alcohol and push it through the printhead '''slowly''' to get the dried ink out. Do this 2-3 times. | |
| * Once you do this, push distilled water through the printhead and do this 5-6 times to make sure the alcohol is out of the printhead. | |
| - | * Dry the printhead spikes with a lint-free cloth. |
| - | |
| + | * Dry the printhead spikes with a lint-free cloth.Once you do this, run a nozzle check and see if it's clear. If not, repeat this until all of the ink comes out of the printhead. Run a nozzle check once a week to keep the ink from drying out if you do not use the printer on a regular basis. |
| + | |
| You have one of the few Epson printers that can have the head removed without damage, but I still do not recommend this unless you are willing to risk destroying your printer. To remove the head you typically remove 2-4 screws and disconnect flat flex cables. You will then soak the printhead rather then use syringes and plastic tubing. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | The problem with these is the head design, and the fact Epson ink is so thick, mainly. This happens on their DuraBrite models too, on a much larger scale, due to how thick pigment ink from Epson is. |
|---|---|
| - | What you need to do to fix the problem is flush the head with distilled water. Warm some distilled water up, and get it nice and hot. This will help break the ink down in the head. Once you do this, put the printer in ink change mode. On these Epsons, this has to be done manually by pressing the ink change button. Once you press it and it's free, you can move the head around freely. Put paper towels under the ink sponge because of how messy this is going to get. You're not going to like what you see. Once you do this, remove the ink cartridges from the printer. |
| - | After you do this, get some plastic tubing, and warm it up with the hot water. You need to warm it up so you create a seal on the nozzles. Warm this up on both sides for the syringe and printer. Get the hot water, and put it in the syringe. Fill it up all of the way, so you have room to put more in. Put the water through '''SLOWLY''' so it can break down the ink in the head causing the problem. Do this 4-5 times, or as many as you need. If you have to add alcohol don't add too much. Only a small amount to assist the cleaning. |
| - | Once you do this, remove the napkin from under the printer. You might want gloves, though. Don't remove the head, since removal on Epson printers seems to destroy them. |
| - | This should fix the problem, given enough tries. Do this until you get a perfect nozzle check. And next time, print one nozzle check every 1-2 weeks, depending on how humid the location of the printer is so you never have to do this again. |
| + | The problem with these is the head design and the thickness of Epson ink. This is more of a problem on the DuraBrite pigment models but the dye based (Claria, etc.) can clog like this just as easily. The best way to fix it is a hot water or 70% alcohol and hot water injection, or removing the printhead and soaking it if you can remove it without damage. Most Epson printers get damaged by mere attempts. You should also be aware of the mess this procedure makes, so wear gloves if you do not want to get ink stains on your skin. |
| + | If you go with hot water and alcohol, here's how you do it: |
| + | * Loosen the printhead. On some models, there will be a white tab you can push to free the head up. On others you will need to put it into ink change mode, remove the cartridges and unplug the printer. The easiest way to tell is to see if the printhead comes to the center when you open the lid. |
| + | * Fold some napkins up and put them in the printer's track. You will need to make sure you do not put too many in or the head will not go there easily. The average is 3-5. |
| + | * Remove the ink cartridges from the printhead. Set these aside somewhere safe. |
| + | * Get a plastic tube and syringe that can accept this tube. Get your 70% alcohol and push it through the printhead '''slowly''' to get the dried ink out. Do this 2-3 times. |
| + | * Once you do this, push distilled water through the printhead and do this 5-6 times to make sure the alcohol is out of the printhead. |
| + | * Dry the printhead spikes with a lint-free cloth.\ |
| + | Once you do this, run a nozzle check and see if it's clear. If not, repeat this until all of the ink comes out of the printhead. Run a nozzle check once a week to keep the ink from drying out if you do not use the printer on a regular basis. |
| + | You have one of the few Epson printers that can have the head removed without damage, but I still do not recommend this unless you are willing to risk destroying your printer. To remove the head you typically remove 2-4 screws and disconnect flat flex cables. You will then soak the printhead rather then use syringes and plastic tubing. |
Status:
open
Bewerkt door: Nick
Tekst:
| - | Ok, before I tell you how i do it, let me explain the problem in 2 words: PIGMENT INKS |
|---|---|
| - | |
| - | I rip the printer apart IF i can find service literature(don't need for some of them) and soak the head in distilled water and put it on a napkin to dry overnight and run the change ink to do it, but this is time consuming and takes 24 hours to dry completely |
| - | |
| - | also dry the nozzles where the inks sit too sepratley and let the head sit on a napkin overnight, and dry every possible portion as well as you can by hand to minimize downtime |
| - | |
| - | If this fails, you could very well be out of luck saving this |
| - | |
| - | In reality, DYE BASED INK IS BETTER for Epson printers! |
| - | |
| - | I know a better method with no disassembly..... get a syringe with no needle from the start and vinyl tubing, distilled water |
| - | |
| - | Take the needle and put distilled water in small increments with a paper towel under the head away form the service station in the printer itsself |
| - | |
| - | Rinse and repeat as needed, but dry the nozzles where the inks go too |
| + | The problem with these is the head design, and the fact Epson ink is so thick, mainly. This happens on their DuraBrite models too, on a much larger scale, due to how thick pigment ink from Epson is. |
| + | What you need to do to fix the problem is flush the head with distilled water. Warm some distilled water up, and get it nice and hot. This will help break the ink down in the head. Once you do this, put the printer in ink change mode. On these Epsons, this has to be done manually by pressing the ink change button. Once you press it and it's free, you can move the head around freely. Put paper towels under the ink sponge because of how messy this is going to get. You're not going to like what you see. Once you do this, remove the ink cartridges from the printer. |
| + | After you do this, get some plastic tubing, and warm it up with the hot water. You need to warm it up so you create a seal on the nozzles. Warm this up on both sides for the syringe and printer. Get the hot water, and put it in the syringe. Fill it up all of the way, so you have room to put more in. Put the water through '''SLOWLY''' so it can break down the ink in the head causing the problem. Do this 4-5 times, or as many as you need. If you have to add alcohol don't add too much. Only a small amount to assist the cleaning. |
| + | Once you do this, remove the napkin from under the printer. You might want gloves, though. Don't remove the head, since removal on Epson printers seems to destroy them. |
| + | This should fix the problem, given enough tries. Do this until you get a perfect nozzle check. And next time, print one nozzle check every 1-2 weeks, depending on how humid the location of the printer is so you never have to do this again. |
Status:
open
Bewerkt door: Nick
Tekst:
| Ok, before I tell you how i do it, let me explain the problem in 2 words: PIGMENT INKS | |
| I rip the printer apart IF i can find service literature(don't need for some of them) and soak the head in distilled water and put it on a napkin to dry overnight and run the change ink to do it, but this is time consuming and takes 24 hours to dry completely | |
| also dry the nozzles where the inks sit too sepratley and let the head sit on a napkin overnight, and dry every possible portion as well as you can by hand to minimize downtime | |
| If this fails, you could very well be out of luck saving this | |
| In reality, DYE BASED INK IS BETTER for Epson printers! | |
| + | |
| + | I know a better method with no disassembly..... get a syringe with no needle from the start and vinyl tubing, distilled water |
| + | |
| + | Take the needle and put distilled water in small increments with a paper towel under the head away form the service station in the printer itsself |
| + | |
| + | Rinse and repeat as needed, but dry the nozzles where the inks go too |
Status:
open
Origineel bericht door: Nick
Tekst:
Ok, before I tell you how i do it, let me explain the problem in 2 words: PIGMENT INKS I rip the printer apart IF i can find service literature(don't need for some of them) and soak the head in distilled water and put it on a napkin to dry overnight and run the change ink to do it, but this is time consuming and takes 24 hours to dry completely also dry the nozzles where the inks sit too sepratley and let the head sit on a napkin overnight, and dry every possible portion as well as you can by hand to minimize downtime If this fails, you could very well be out of luck saving this In reality, DYE BASED INK IS BETTER for Epson printers!
Status:
open