Ga door naar hoofdinhoud
Help

Deze versie is geschreven door: John b. ,

Titel:

DIY headunit harness fabrication

Tekst:

'''Aftermarket Reverse Harness RCA Trouble''
-Hello folks! After 6 months of back-and-forth with Chinavasion's many departments, Ive concluded that they want absolutely nothing to do with a peraon after they buy a product. Hence, Im left to fabricate my own reverse harness for this headunit handmedown myself. Normally, no big deal....but I've run across an anomoly that i hope someone can shed some light on....
+Im installing a double din Chinavasion "Stargate" touchscreen headunit, complete with GPS, DVD, and the other fancy stuff. A bit dated, but im po'.....not "poor"..."po". The schematic on the top of the unit shows the pinout, and that should make this a quick job, but for the RCA outs that will feed my amplifier.
-Im installing a double din Chinavasion "Stargate" touchscreen headunit, complete with GPS, DVD, and the other fancy stuff. A bit dated, but im po'.....not "poor"..."po". The schematic on the top of the unit shows the pinout, and that should make this a quick job, but foe the RCA outs that will feed my amplifier.
+It shows 2 sets of RCA's...
-It shows 2 sets of RCA's. Set ONE, is fed from 3 pins.....and set TWO is fed from 2 pins. How in F-......? I can see them using a 3 pin XLR setup with a shared shield that splits to either side. And then again, just as likely theyd use a L and R setup with the two pin....but why a seperate type for both?
+ Set ONE: Is fed from 3 pins.....
+ Set TWO: Is fed from 2 pins...
-My multi channel amp requires 4 inputs for front,back,left,right and i really dont wanna damage this unit accidentally. However, after 6 months without any tunes im vlose to saying the !&&* with it and just rolling the dice and seeing what happens.
-
-Thanks in advance, and ill do my best to answer any questions i can...which is why ill never work for Chinavasion.
+How in F-......?
+Thanks in advance, and ill do my best to answer any questions i can...which is why ill never work for Chinavasion. They refuse to provide an explaination, photo of an original, or to sell me a new one

Apparaat:

Car Audio

Status:

open

Origineel bericht door: John b. ,

Titel:

DIY headunit harness fabrication

Tekst:

'''Aftermarket Reverse Harness RCA Trouble''

Hello folks! After 6 months of back-and-forth with Chinavasion's many departments, Ive concluded that they want absolutely nothing to do with a peraon after they buy a product. Hence, Im left to fabricate my own reverse harness for this headunit handmedown myself. Normally, no big deal....but I've run across an anomoly that i hope someone can shed some light on....

Im installing a double din Chinavasion "Stargate" touchscreen headunit, complete with GPS, DVD, and the other fancy stuff. A bit dated, but im po'.....not "poor"..."po". The schematic on the top of the unit shows the pinout, and that should make this a quick job, but foe the RCA outs that will feed my amplifier.

It shows 2 sets of RCA's. Set ONE, is fed from 3 pins.....and set TWO is fed from 2 pins. How in F-......? I can see them using a 3 pin XLR setup with a shared shield that splits to either side. And then again, just as likely theyd use a L and R setup with the two pin....but why a seperate type for both?

My multi channel amp requires 4 inputs for front,back,left,right and i really dont wanna damage this unit accidentally. However, after 6 months without any tunes im vlose to saying the !&&* with it and just rolling the dice and seeing what happens.

Thanks in advance, and ill do my best to answer any questions i can...which is why ill never work for Chinavasion.

Apparaat:

Car Audio

Status:

open