el tambor de mi lavadora LG INVERTER DIRECT DRIVE 22/13kg

⟐ Answered november 04, 2025 at 2:38 MST

⟐ Answered juni 26, 2025 at 1:33 MST

⟐ Answered juni 18, 2025 at 11:24 MST

Nu wil ik hem open maken. De borgring op de as verwijderd om de rotor te verwijderen. Maar krijg de rotor niet los.

Hoe moet dat? Met een poelietrekker? Of eerst verwarmen?

Iemand ervaring hiermee?

⟐ Commented maart 29, 2020 at 15:12 MST

Ik hebeen wasmachine van samsung een ecobubble tm van 8 kg. Deze is zeker al 5 jaar oud.

Nu is hier juist een hersteller hier geweest dij mij melde dat de printplaat stuk is. En dat dit ons 350€ tot 400€ gaat kosten om dit te maken.

Nu wil ik dit wel zelf eens vervangen.

Maar begin ik hieraan?

Als ik een foto kan nemen van de printplaat dan kan ik via een site dezelfde printplaat kopen.

Wie wil mij hiermee verder helpen?

Alvast bedankt voor jullie hulp.

Michael

⟐ Answered november 15, 2019 at 15:21 MST

I'm also change the pressure switch

And inlet

But it showing IE error

⟐ Answered augustus 15, 2026 at 9:10 MST

⟐ Answered augustus 15, 2026 at 7:20 MST

Lint filter is clear

Waste hose is clear with no kinks

Drain pump replaced

Hoses from drum to pump clear

Water level sensor clear but not replaced.

Any ideas

⟐ Answered augustus 14, 2026 at 12:25 MST

⟐ Answered augustus 13, 2026 at 14:26 MST

⟐ Answered augustus 12, 2026 at 23:27 MST

⟐ Answered augustus 12, 2026 at 21:30 MST

Now, the cycle starts and water sprays in the machine, then the water runs through the detergent cup. The machine spins to balance the load, and when the tub slows to fill, nothing happens. Doesn't matter what cycle or water temperature, no water is added to the main tub for about the first 8 minutes of the cycle. After that, it kicks in and starts adding water, washes, rinses and drains as normal. I'm not getting any error codes.

We checked hoses, water pressure and screens. Thought it might be the water intake valve, but since it's working at other stages in the cycle, it's not that. Does this mean I have a timing issue or something with the main computer component? Again, I've not had any problem that I was aware of until we moved it after it'd been in the same place for 7 years.

Thanks for your help!

⟐ Edited augustus 13, 2026 at 1:55 MST

It also stopped before the cycle ended. Had to CC unplug to open the door

⟐ Answer edited augustus 14, 2026 at 0:31 MST

⟐ Answer edited augustus 12, 2026 at 18:26 MST

⟐ Answered augustus 12, 2026 at 0:31 MST

This started after an overloaded wash. Even after removing the clothes (or running it completely empty), it keeps doing the exact same thing. I’ve already checked the suspension rods (it doesn't shake) and the safety switch, and both seem fine. Any ideas on what else could be wrong?

⟐ Commented augustus 11, 2026 at 22:25 MST

Our washer makes this strange noise during the wash cycle, like a whining or squeaking sound. It almost sounds like rotating something on dry rubber.

The spin cycle is silent and it’s not when the washer is filling. I can duplicate the sound by grabbing the inner tub and rotating it in either direction.

I can’t see it being the felt pads on the outside of the tub because tilting the tub during rotation does change the sound.

Anyone have any ideas what it could be?

Thanks

Darryl

⟐ Commented augustus 11, 2026 at 16:56 MST

I need some help please

I have a WW85M74FNOR Samsung front loader washer, it turns on locks the door adds water then goes into pause and will not spin if placed in drain and spin mode, found that this unit has 2 x motors, when I removed the back panel.

kind regards

Sash

⟐ Commented augustus 11, 2026 at 14:08 MST

⟐ Commented augustus 09, 2026 at 21:33 MST