⟐ Commented april 02, 2025 at 23:47 MST

Ik heb zojuist het scherm vervangen van een iPad 9 Gen 2021, deze was helemaal gebarsten. Echter na het testen van alle functies krijg ik bij de camera aan de voorkant de melding "iPad moet eerst afkoelen voordat de flits kan worden gebruikt". Nou zit er sowieso geen flits in dit apparaat en dacht ik eerst dat ik de camera had beschadigd. Maar ook met een nieuwe camera geeft het apparaat dezelfde melding. Heeft iemand enig idee wat dit kan zijn?

⟐ Commented juli 20, 2023 at 0:57 MST

⟐ Edited maart 12, 2023 at 10:00 MST

Vandaag had ik een iPad 5 binnen met een kapotte digitizer en LCD die geen beeld meer gaf. De LCD connector had waterschade dus heb ik een nieuw digitizer geplaatst met nieuw LCD.

Nu echter start de iPad op zonder Apple logo, de backlight gaat aan en hij start gewoon op. Na een 10tal seconden kom ik in het homescreen en kan ik er gewoon met werken.

• Update al uitgevoerd
• Restore al uitgevoerd

Home button zit er nog niet op omdat er een nieuwe onderweg is.

Aan wat kan dit liggen? Voor de rest doet de iPad perfect normaal.

Ik heb het volgende probleem met mijn ipad 2.

Kan hem niet meer opstarten. Geeft aan dat ik de connector aan moet sluiten via de usb

op mijn computer. Itunes met laatste update opgestart. Geeft aan dat dat de software wordt bijgewerkt naar 9.3.5. Geeft daarna dat dit mislukt is met code 9.

Heb op advies van apple:

- firewall uitgeschakeld

-andere usb poort gebruikt.

Hij blijft terugkomen met code 9.

Wie kan mij helpen.

⟐ Answer accepted oktober 11, 2017 at 3:34 MST

Rep: 1 1 Missed: yesterday

 Options

Power button cable connections

A good day all.

I have the following problem.

I have an iPad 2 and replace the power button cable, but there still remains at the end of a connection!

Look at the IPad laying down with the powerknob at the right upper site.

Then starting from top right side towarts down.

1. connection cable from the power button - then connection to the switch for the Wi-Fi - then the two switches of the volume knob. Then there's one connection left over.

On surtain movies you can see that this connection is a ???? thing, which is below the volume button. What is this thing? Becuase my IPad 2 has not such thing.

Please help.

Greetz

Aad.

Sorry for my bad Englisch.

Please help.

Greetz

Aad.

⟐ Commented december 02, 2015 at 7:04 MST

⟐ Answer unaccepted mei 08, 2026 at 20:35 MST

I replaced the battery of my iPad 2 with the new iFixit one but now it is stuck in a boot loop. I tried my old battery and it shows a low battery sign but the new battery just puts the iPad in boot loop. I tried the Home button + power button reboot thing but it didn't work. Could it be that the new battery might be faulty?

Thanks for any help :)

⟐ Commented mei 07, 2026 at 11:49 MST

Could you help me out and provide advice please ?

Thanks

⟐ Answered mei 05, 2026 at 7:56 MST

Could you you provide me some advice please ?

Thanks

⟐ Answered april 20, 2026 at 5:18 MST

⟐ Answer accepted april 19, 2026 at 10:53 MST

The sound on my iPad all of a sudden stopped working. The sound works fine with headphones in and I can change the volume, but when I unplug the headphones I get absolutely no sound from the speaker, and I can't even change the volume.

I originally thought this must have been a software issue so I went through all the settings, checked mute etc.

After that, I tried a reset using the power and home button, and I even restored to factory settings.

I then changed the speaker with a new one, still no luck.

I have now changed the headphone jack as I thought this may have been interfering, but there is still no sound.

Any help would be very much appreciated!!!

Thanks,

Michael

⟐ Commented april 17, 2026 at 17:27 MST

⟐ Answered april 16, 2026 at 21:34 MST

I replaced the battery but still getting the TG0B error. The battery level is fluctuating as well. I checked the capacitor C8923 and I got diode resistanc f .883 not sure if this is too high. FL8900 is good as well. What Iam not sure is the Q8900 which for BATT_SWI_FL.

The C8922 which is for BATT_NTC is ok as well it go straight to PMU chip. I tried to jump a wire from the battery terminal directly to batt_ntc n C8922 in case the connection going to the battery is loose but still getting TG0B ... This issue is a pain.

⟐ Answered april 15, 2026 at 9:16 MST

Reboots are not spaced evenly at 180s apart, which probably indicates the sensor is responsive at times and not at others? At the beginning of the issue, I could sometimes use it for 5-10 minutes without rebooting, and sometimes less. Charge level fluctuates around 10-20% on each reboot and just randomly when unlocked. The reboots got more frequent and regular over time. Last night it seemed the iPad was charging very slow.

I took it for repair today,

They replaced the battery and the issue persists.

I've read TG0B is an NTC thermistor in the battery.... what could be the next steps? Any possible issues in the measurement circuitry?

panic(cpu 0 caller 0xfffffff0243a0514): userspace watchdog timeout: no successful checkins from thermalmonitord
service returned not alive with context : is_alive_func returned unhealthy : current 1ffffffe, mask 1fffffff, expected 1fffffff. EC: 1 EH: 3758097110 3758097110 SD: 0 BC: 0 RC: -1 BS: 0, Missing sensor(s): TG0B

⟐ Commented april 15, 2026 at 9:11 MST

I got an iPad 9th gen WiFi battery replacement kit. I tried using iopener multiple times as instructed. I even used a blow dryer directed the heat towards the display in a blanket. The display didnt budge at all!

Is it possible to use the adhesive remover that came with the kit and put it along the display? Is there anything i should know about this? like would it ruin the device or the display if i am still unable to open the display?

⟐ Commented april 11, 2026 at 13:17 MST

⟐ Commented april 02, 2026 at 17:54 MST