iFixit - Answers With Device "Power Tool"

Bosch PBH 3000-2 FRE: Machine valt stil en na kwart slag draaien van machine werkt hij weer

Tue, 04 Aug 2026 00:44:52 -0700

De machine valt soms stil tijdens het boren of wil niet starten. Als je de machine dan een kwart slag draait doet hij het weer. Heel merkwaardig en super onhandig. de machine heeft heel veel stof gezien. Is er een contact dat kan vervuilen intern ?

⟐ Answered augustus 04, 2026 at 0:44 MST

Power Drill: Demonteren van een Bosch GBH 2-23

Sat, 08 Nov 2025 14:09:14 -0700

Hallo

IK wil deze klopboormachine uit elkaar halen om er nieuwe vet in te doen

Heeft iemand een tip om de keuze schakelaar te demonteren en of heeft iemand dit al eens gedaan

Groet

Freddy

⟐ Answered november 08, 2025 at 14:09 MST

Bosch PBH 3000-2 FRE: Boorhamer (Bosch PBH 3000-2 FRE) reageert totaal niet

Sun, 21 Jan 2024 23:44:31 -0700

Tijdens het verwijderen van pleister (stucwerk) verminderde plots het vermogen(slagkracht) en waren er achteraan (zichtbaar door de ventilatiegleuven) meer vonken/glinsters te zien dan anders. Daar ik slechts nog een heel klein stukje moest doen werkte ik nog even door met na enkele seconde als gevolg een licht plofgeluid en niets meer. De machine doet helemaal niets meer onafhankelijk de stand (boren/beitelen).

Door de extra vonken/glinsters en het vermogen verlies dacht ik aan de koolborstels. Echter ondanks deze machine al ouder is dan 10 jaar is hij heel weinig gebruikt (enkele uren max 10uur) en als ik hem open, lijken de koolborstels nog vrij goed (lang) en goed contact te maken.

Heeft iemand een idee wat het zou kunnen zijn (toch koolborstels of iets anders)? Advies/tips hoe ik het kan analyseren/diagnosticeren worden zeker gewaardeerd.

Alvast bedankt.

Mvg,

Sam

⟐ Answer accepted januari 21, 2024 at 23:44 MST

DeWalt D28110: Why is my grinder spinning so slowly?

Sat, 29 Aug 2026 11:10:31 -0700

The power source/outlet that I am using works fine, but my tool is not spinning as fast as it should.

⟐ Commented augustus 29, 2026 at 11:10 MST

Dewalt Rotary Hammer DCH133B TYPE 1 2016: DCH033 Chuck Won't Hold Bits

Thu, 27 Aug 2026 17:15:02 -0700

The chuck on my Dewalt hammer drill DCH033 won't hold bits. I purchased a chuck repair kit, but that wasn't the problem. There's a gap below the sliding tube that should not be there, and I can't figure out why or how to fix it. The drill is fairly new and has only been used a few times.

FixHub Smart Soldering Iron: FixHub Web Console Connection Error on Ubuntu(Solved: user permission)

Wed, 26 Aug 2026 14:08:37 -0700

I was encountering a "Connection error" when trying to connect my FixHub Smart Soldering Iron to the web console at ifixit.com/fixhub/console. I am running Ubuntu 24.04.2 LTS and using the latest Google Chrome browser.

The error message stated: "Make sure you do not already have another connection open and try again."

I tried the following troubleshooting steps without success:

Fresh boot with no other applications or browser tabs open.
Tried multiple USB ports.

The solution that worked for me was adding my user account to the dialout group. I used the command: sudo usermod -a -G dialout (replacing with my actual username). After running this command and then logging out and back in, I verified I was added to the group using groups and was then able to connect to the web console successfully after a reboot.

This seems to be a common permission issue on Linux systems for accessing serial ports.

⟐ Commented augustus 26, 2026 at 14:08 MST

Dewalt Impact Driver DW290 TYPE 2 2012: Hooking up wires on switch

Wed, 26 Aug 2026 10:57:25 -0700

We're do the wires go

Toshweld ARC-200: Toshweld ARC-200 inverter welder: fan works but display and power ligh

Wed, 26 Aug 2026 06:12:29 -0700

I have a Toshweld ARC-200 inverter welding machine.

The problem is intermittent. When I turn the machine ON, the cooling fan runs, but the digital display does not turn on and the green power LED does not light up. There is also no welding output.

The power switch has been checked and it is working correctly. When the power switch is ON, the fan runs. When the power switch is OFF, the fan stops.

Previously, the same problem occurred. The next day I turned the machine ON again and it worked normally: the display came on, the green power light came on, and the welding output worked. Later, the same fault returned and now the fan runs but the display, power light and welding output do not work.

The machine specifications are:
Model: ARC-200
Input: 220/230V, 1 phase, 50/60Hz
Rated output: 200A
No-load voltage (Vo): 62V
Duty cycle: 60%

I want to troubleshoot and repair this machine step by step. Please help me identify which section I should check first. In particular, I would like to know where the auxiliary/control power supply for the digital display, green power LED and welding control circuit comes from after the main power switch.

I have a basic electrical tester and screwdrivers, but I currently do not have a digital multimeter with test leads.

I can provide photos of the machine and PCB if needed.

⟐ Commented augustus 26, 2026 at 6:12 MST

Makita Circular Saw BSS611Z 2008: Stopped running wont work

Tue, 25 Aug 2026 15:15:11 -0700

It dosnt run

⟐ Commented augustus 25, 2026 at 15:15 MST

Ryobi Jig Saw JS651L1 2012: Orient and install torsion spring

Sat, 22 Aug 2026 18:38:43 -0700

How to orient and install the torsion spring on the blade guide.

FixHub Portable Power Station: PowerStation bricked after firmware update

Wed, 19 Aug 2026 20:47:20 -0700

Hi,

I just purchased my FixHub Soldering Toolkit today and decided to upgrade to the latest firmware. It came with 1.0.3 and after upgrading to 1.0.7 it no longer detected the soldering iron. I decided to downgrade back to 1.0.3, but this errored during the 'resetting device' stage after it uploaded the firmware.

The display no longer shows anything at all and the device seems to not power on. I opened it and disconnected the battery for 10 minutes then reconnected it and tried to power it on with no luck.

I can put the device into DFU mode by holding down the silver knob while connecting a USB cable to the back port. It will load up in the web console, but it still shows 1.0.7 on the device and no downgrades succeed nor will the device power on.

Please help!

⟐ Commented augustus 19, 2026 at 20:47 MST

SKIL 4235 Jigsaw: Replacement part for holding blade onto saw

Wed, 19 Aug 2026 13:43:35 -0700

My saw no longer holds blades tightly. The "key" just keeps turning in the "collar". The threads on either the key or inside the collar must be worn or damaged. Can I remove and replace the "collar" device? Removal instructions would be helpful.

Dennis

⟐ Answered augustus 19, 2026 at 13:43 MST

Power Tool: Hart 20v battery repair

Wed, 19 Aug 2026 10:19:23 -0700

Repair specs?

⟐ Answered augustus 19, 2026 at 10:19 MST

Makita Drill Driver 6095D 1995: Why is my charger not charging my batterie

Mon, 17 Aug 2026 22:55:35 -0700

Why charger won't charge the batteries

Makita Circular Saw 5008MGA 2014: كيف اصيد القاعة على درجة 45

Sat, 15 Aug 2026 11:43:58 -0700

إعادة ضبط القاعدة

Bosch Hammer Drill HD182 2016: The chuck on my drill is stuck and won’t come off

Fri, 14 Aug 2026 06:40:16 -0700

Cant remove chuck tried with chuck keys and it’s solid what do I do

⟐ Answered augustus 14, 2026 at 6:40 MST

Dewalt Nailers DWFP12233 2016: nail driver pops out when I connect air compresser

Tue, 11 Aug 2026 17:53:56 -0700

how to fix !!

⟐ Commented augustus 11, 2026 at 17:53 MST

Dewalt Air Compressors DWFP55126 2016: Compressor stays at max pressure

Mon, 10 Aug 2026 16:57:14 -0700

My DeWalt compressor regulator is inoperable and stays at max pressure. How do I replace the regulator?

⟐ Answered augustus 10, 2026 at 16:57 MST

Rotozip: My Rotozip RZ220 wont start. Is there a reset button?

Fri, 07 Aug 2026 11:35:10 -0700

My Rotozip RZ20 wont start

FixHub Smart Soldering Iron: Is there documentation for the serial console

Tue, 04 Aug 2026 18:08:31 -0700

Is there any documentation for using the serial console when directly connecting the smart soldering iron to a PC?

The web console is great but not always an option if you are in an offline environment. I see that there is a basic help command but it does not seem to give much detail on individual command usage.

⟐ Commented augustus 04, 2026 at 18:08 MST