⟐ Commented oktober 13, 2025 at 7:28 MST

⟐ Commented april 12, 2024 at 8:35 MST

⟐ Commented december 20, 2025 at 8:28 MST

Is there a brightness control anywhere? Or do we need to replace the display?

⟐ Answer accepted februari 06, 2026 at 6:04 MST

⟐ Commented juni 16, 2025 at 10:15 MST

⟐ Answered november 16, 2025 at 11:10 MST

flashing inside microwave, just like having a metallic object in oven. thanks ray

⟐ Edited december 22, 2023 at 11:15 MST

Now, the top won't close. When I look inside to see what's blocking it, I see a metal tongue back behind the K-cup holder and a bar that looks like it's supposed to slide over the tongue and into a groove. However, the tongue is completely rigid and locked in place, such that the bar would have no hope of sliding back into the groove. I'm assuming the tongue is supposed to have a little give so that the bar can slide over it into the the groove, but since it's rigid, it's impossible to force the handle closed against that pressure.

I didn't mess with anything in this part of the machine - my fingers wouldn't even fit back there. Did I inadvertently mess something up when I slid the top of the housing off to look at the tubes? Help!

Edit:

I added pictures of the metal tongue and the bar I'm talking about, as well as a photo showing how the Keurig won't close. The photo shows as far down as the handle will go in its current state.

⟐ Commented april 24, 2022 at 7:46 MST

My grinder is not similar to the ones in the instructions. It's the same model, but it looks different inside. The blades are fasten with something that looks like a plastic nut on top. I´ve tried pulling on the blades, but it doesen´t seem to work. I´ve also tried to undo the nut, my tools are causing damage to the nut.

Do anyone know if this is a nut, or pulling harder is the solution? And if so, do anyone know if it is a right or left threaded nut (normal or lynx)?

My problem with the grinder is that the blades wont turn. The motor is working, but of some reason, either the rotor in the motor or the blade assy is stuck.

Thanks!

⟐ Commented januari 17, 2026 at 13:07 MST

Mike Jordan.

⟐ Commented december 09, 2022 at 23:52 MST

This is my third machine I’ve received from Keurig support and it’s still happening. I’ve done all the needle cleaning, reseting, descaling, and many other fixes. The unit is not even 3 months old.

I’m just at a loss of what to do because I don’t see many people having the same problem. I’m also sick and tired of wasting perfectly good K Cups! Anybody have ideas how to permanently fix this?

EDIT & SOLUTION: I've been able to resolve the issue using a work around. This is not a fix and I don't know why Keurig hasn't fixed it after years of this happening.

When using a milk based K Cup, press it into the bottom by hand so the K Cup is punctured. Pull it up and rotate 90º and close the lid. This gives the K Cup two holes and much less pressure. It has worked perfectly since I've been doing this.

⟐ Commented maart 26, 2026 at 9:57 MST

which no longer works. it was purchased 11/29/14. The lid will no longer close.

is there a solution to this problem.

⟐ Commented november 13, 2025 at 12:02 MST

⟐ Commented november 02, 2024 at 15:30 MST

⟐ Commented januari 29, 2025 at 20:19 MST

⟐ Answered april 24, 2022 at 11:17 MST

⟐ Commented november 27, 2023 at 16:00 MST

⟐ Answer edited januari 29, 2026 at 20:36 MST

⟐ Commented april 24, 2024 at 22:09 MST

⟐ Answered februari 10, 2025 at 13:58 MST

Got a Ninja NJ600 from the States (120v) and wanted to use it in Europe (240v). But, had an accident and got plug in to a 240v power plug directly, and of course it went silent.

I have dismounted the unit and made a number of pictures. Of this the electronic board was burn in one area.

I need to know first, if this information and pictures are enough to get a response?

Second, how I can I fix it?

And last, can I make it 240v capable?

Thank you in advance.

Jacobo PM

⟐ Commented november 23, 2025 at 11:20 MST