iFixit - Answers With Device "DJI"

DJI Mini 4 Pro: Nieuwe dji mini 4 pro gaat niet aan

Wed, 06 Aug 2025 03:51:37 -0700

Ik heb een nieuwe dji mini 4 pro. Accus zijn vol en nog steeds gaat de drone niet aan. Wat moet ik doen?

⟐ Answered augustus 06, 2025 at 3:51 MST

DJI Phantom 3 Standard Remote Controller: Waarom kan mijn RC niet meer opladen?

Sun, 12 Aug 2018 10:27:55 -0700

Ik ben op vakantie gegaan met mijn phantom 3 standard en ineens kan ik de rc niet meer laden. Ik weet niet hoe ik dit kan oplossen.

DJI Mini 3 Pro: The data from the gamble is inconsistent.

Fri, 17 Apr 2026 21:48:20 -0700

The data from the gamble is inconsistent.

DJI FPV Drone: Why is my fpv drone not turning on after replacing the vision sensor c

Tue, 14 Apr 2026 15:32:25 -0700

How to fix it

DJI Mavic Mini: DJI Mavic Mini IMU calibration "Start" button not working/greyed out

Mon, 13 Apr 2026 20:16:37 -0700

I'm experiencing an IMU error on my DJI Mavic Mini. When I navigate to the 'Safety' -> 'Sensor' -> 'IMU' -> 'Calibration' menu in the DJI Fly app, the 'Start' button is visible but completely unresponsive (it won't click or is greyed out).

Current setup:

- DJI Fly App version: 1.20.0

- Aircraft Firmware: 01.00.0600 (latest version)

- Battery level: Above 50%

- Surface: Flat and level

- Arms: Folded in

I have already tried restarting the drone, controller, and app multiple times. I have also tried the correct power-on sequence (controller then drone). What could be preventing the calibration from starting? Is this a known software bug with this app version, or does it indicate a total hardware failure of the IMU chip on the motherboard?

DJI Mini 4 Pro: landing senser not working

Mon, 13 Apr 2026 01:25:27 -0700

landing sensor not working

Mavic Air (1st Gen): How to revive a battery that has totally died.

Wed, 08 Apr 2026 04:57:23 -0700

I can't charge the battery of my Mavic Air, first generation. It went down to zero during flight.

⟐ Commented april 08, 2026 at 4:57 MST

DJI Phantom 3 Standard: Gimble gyroscope error after replacing ribbon cable

Tue, 07 Apr 2026 21:39:45 -0700

Replaced ribbon cable after mild crash and am getting gimbal gyroscope error message and no movement though I can hear the motors attempting to move the gimbal. Picture is fine and drone will fly. Compass will not calibrate but I am used as calibration is fine and compass is calibrated as well according to the drone

DJI: Mavic 3t sensor system issuse

Sun, 05 Apr 2026 22:51:23 -0700

I have replaced the middle frame of mavic 3t after replacement it is showing Initiliazing sensor system error and Flight control system error. What is the possible cause.

⟐ Commented april 05, 2026 at 22:51 MST

DJI: Aircraft bound to another account….

Wed, 01 Apr 2026 16:52:58 -0700

Hi,

I purchased a Mavic Air 2S from EBay but I’m getting an error on the DJI Fly app that says

“Aircraft bound to another account. Change account and try again.”

I tried to reach the seller and no response. Is it possible to “unbind” the Air 2S from the previous owners DJI account?

⟐ Commented april 01, 2026 at 16:52 MST

DJI Mavic Mini: Gimbal flex broken replacement

Wed, 01 Apr 2026 09:27:44 -0700

I need a replacement on gimbal flex

DJI Mavic Pro: Where I can buy a service repair manual for the dji mavic pro

Tue, 31 Mar 2026 20:22:43 -0700

Crashed my mavic for the first time. Accidently hit the return home button and panicked. Long story short hit a tree and fell 30 feet. Gimbal is erratic and front vision sensor error. Just wondering if there was a service/ repair manual to refer during the repair.

⟐ Answered maart 31, 2026 at 20:22 MST

DJI Mavic 3: Mavic 3 classic display unit

Sat, 21 Feb 2026 08:50:02 -0700

I bought an crashed dji mavic 3 classic and i cant bind it to my controller i cant see wideo feed. dji assistant told me it will be working fine after my repair turns out its not working well. i cant refund it becouse time for refund its up and i just dont know what to do.. any suggestions?

DJI Mini 3 Pro: Extreme water damage guidance

Mon, 16 Feb 2026 13:26:59 -0700

I just bought a DJI mini 3 pro that turns out to have severe water damage (it's a little complicated, but I'm not too disappointed). Shockingly, it mostly works (no errors, only the rear right motor has a little more resistance than the rest so it can't quite fly); the previous owner didn't even know it was water damaged. It's been at least a week since it got wet, likely much longer. I'm going to follow this tutorial to clean off the motherboard, replace the ESC entirely, and probably follow the same steps for the camera module (is this safe?). However I have a couple questions:

What is that white stuff? It seems to have been used to glue some of the connectors, but whoever did this obviously didn't actually fix the water damage.
Should I do anything extra/differently because it's been corroding so long?
Can I do anything for the motors (flight and gimbal)?
Are there any listings for the thermal paste on amazon that could arrive quicker with prime? I couldn't find any.

DJI Phantom 3 Pro: Wire to board connector

Thu, 12 Feb 2026 14:14:56 -0700

For the camera gimbal, there's a gray 8pin wire-to-board connector which broke. I don't want to buy the whole cable set IF370-007-1, and also it's out of stock - but maybe someone can tell me the exact part number of the white connector case. The crimps are all still intact.

DJI Mini 2: Why won't my camera work even after I repaired it

Tue, 10 Feb 2026 17:11:09 -0700

I crashed my drone, and the camera wire attached to it broke as well as the gimbal holder. I repaired the gimbal holder just fine, no problem there. When i fixed the camera flat wire and closed the drone back up, the camera would not connect when powered on. It still flies, but the camera wont show on the phone.

⟐ Answered februari 10, 2026 at 17:11 MST

DJI Mini 3: Errors on mini 3 after repairs

Sun, 08 Feb 2026 17:46:41 -0700

I recently got a DJI mini 3 with a broken front left arm. These are all the repairs I have done and the state of the drone after each:

Replaced front left arm
- Broke GPS ribbon cable
- Small plastic cube came off the gimbal cable
Replaced GPS ribbon cable with one from a M4p
- Now flies
- Gimbal stuck error (yaw/roll don't move, but all axes move manually)
Replaced gimbal cable with one from a M4p
- Damaged pitch motor ribbon cable during disassembly, replaced arm and motor with one from a M4p
- Gimbal is now detached from the drone
- No errors, gimbal moves when held
Reattached gimbal
- Gimbal does not move, no video feed
- Tons of errors (see pictures)

I'm confused by the downward vision sensor error. I didn't mess with anything but the gimbal after I got it working while detached other than to try and address these issues.

DJI Mini 2: Drone does not respond to controller

Tue, 03 Feb 2026 12:48:24 -0700

I have not used my Mini 2 in a couple of years because of restrictions where I used to live. Now, I have updated all firmaware and fully charged the batteries and the light on the aircraft blinks green. The controller connects to the aircraft, and I can see the image that the aircrtaft sees, on the iphone.. However, the propellors will not respond to the controller, If I press the auto takeoff button, or use the joysticks, nothing happens at all. Any suggestions gratefully accepted.

⟐ Answered februari 03, 2026 at 12:48 MST

DJI Mini 2 SE: Downward or forward vision sesnor error

Wed, 28 Jan 2026 11:50:45 -0700

My drone crash landed and its showing this error:downward vision sensor error

⟐ Answered januari 28, 2026 at 11:50 MST

DJI Goggles: Why won’t turn on

Thu, 22 Jan 2026 10:01:55 -0700

Have a DJI FPV that the DJI goggles 2 will not turn on even though battery charged. Possible problems and how to rectify?