Camera heeft natuurlijk geen echte waarde meer maar voor mij wel (geschenk).

Ook heeft hij nog niet eens het antal clicks die ik regelmatig voorbij zie komen.

Wie heeft voor mij de oplossing of kan hem repareren?

⟐ Answered januari 11, 2026 at 3:21 MST

⟐ Answered augustus 18, 2020 at 14:13 MST

de modusschakelaar (knop waaraan je draait om van modus te veranderen) van mijn fototoestel is losgekomen (afgekraakt?). hierdoor kan ik enkel nog de optie ‘filmen’ gebruiken. ik kan dus niet meer kiezen voor een andere ‘modus’.

1) kan ik die knop terug vastmaken op het toestel? (bv lijmen)

2) kan ik veranderen van modus zónder de knop. Onder de knop, op het toestel zelf dus, zie ik 3 “randjes”. Heb geprobeerd om daaraan te draaien maar lukt niet. (zou het binnenin geblokkeerd zijn?)

Thank you very much !! greetings Liz

Alvast bedankt !! groetjes Lies

⟐ Answer accepted januari 26, 2020 at 9:13 MST

⟐ Commented mei 19, 2019 at 23:51 MST

Google translation

the contact between the battery and the device is interrupted

⟐ Answered juni 15, 2017 at 2:33 MST

⟐ Edited mei 30, 2017 at 11:39 MST

⟐ Answered december 29, 2016 at 8:25 MST

⟐ Answered mei 29, 2016 at 10:42 MST

⟐ Commented mei 22, 2026 at 6:50 MST

⟐ Answered mei 16, 2026 at 1:55 MST

⟐ Answered mei 15, 2026 at 20:41 MST

When I met with the seller, upon powering it on, briefly the camera settings (such as ISO and Shutter Speed) could be seen in the viewfinder, however the LCD stayed black. The flash too would work during this time.

Everything that was working:

• Camera Settings in the viewfinder
• Flash would actuate, not actually flash
• Auto-focus

Things that weren't working:

• Camera mirror
• LCD

I followed the guide to replace the LCD but instead of replacing it, I unplugged and replugged the screen. When assembling it all again, I now have nothing showing, in the viewfinder or LCD. The flash is now no longer working.

Everything now not working:

• Flash Actuation
• Camera Settings
• Auto-focus maybe??
• Everything that wasn't working originally

I should also mention I have tested that the lens recieves power with a multimeter. I also checked the LCD and it recieves ~4.5V on what I assume is the main power line for it, other components recieve 3.3V and 1.8V. I have checked the battery too and am getting 7.4V+.

I am not too sure where to look now and would like some pointers on where to look next. In the meantime, I will probably end up tracing all the circuits or checking the viewfinder display to find why that stopped working.

Updated: Things Checked/Done:

• Unplugged and replugged all cables on the front panel.
• Checked every capacitor/volatile component.
• Unplugged and replugged all cables to the motherboard, during this found that the on/off switch ribbon was almost out.
• Manually actuated the flash and mirror gearboxes, they reset (and scared me) when reassembled and powered on.
• Tried two different batteries, both fully charged.
• Tried with and without SD card.

Thank you for your time.

⟐ Commented mei 14, 2026 at 23:06 MST

⟐ Answered mei 13, 2026 at 10:17 MST

⟐ Commented mei 13, 2026 at 6:41 MST

After being exposed to water, it looks like there is a problem with it. every now and then the camera asks me to setup date and time.

Thanks for any help!

⟐ Commented mei 12, 2026 at 5:19 MST

⟐ Edited mei 11, 2026 at 15:26 MST

My camera Canon Power Shot A4000 IS HD doesn't open the lens, when i try to start it, it says "Lens Error" and says to restart but its no working... Can someone help me ? What should I do ?

⟐ Answered mei 11, 2026 at 2:32 MST

⟐ Commented mei 10, 2026 at 9:36 MST